Huafeng Xiao

Prof. Huafeng Xiao

School of Electrical Engineering, Southeast University, Nanjing 210096, China

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 June 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Huafeng XiaoHuafeng Xiao
Huafeng Xiao
Transformerless grid-connected inverters (TLI) feature high efficiency, low cost, low volume and weight due to using neither line-frequency transformers nor high-frequency transformers. Therefore, TLIs have been extensively investigated in academic community and popularly installed in distributed photovoltaic grid-connected systems during the past decade. This paper analyzes and summarizes the state of the art of TLI techniques, three rules of maintaining constant common-mode voltage (CMV) of TLIs at switching frequency have been concluded from a generic CMV analysis model at the beginning. Secondly, suppression methods of leakage current (LC) and DC current injection (DCCI), so called as two key challenges for first generation TLIs, have been classified and discussed in detail, respectively. Finally, future trends and some challenges of TLIs based on wide bandgap devices named as second generation TLIs in this paper have been presented.

27 September 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ZWZheng Wang
Zheng Wang
YZYue Zhang
Yue Zhang
SYShuai You
Shuai You
Huafeng XiaoHuafeng Xiao
Huafeng Xiao
Ming ChengMing Cheng
Ming Cheng
An integrated power conversion system is proposed for electric vehicles (EVs), which consists of a dual active bridge (DAB) DC-DC converter cascaded by a three-phase four-leg (TPFL) DC-AC converter. The integrated power conversion system can realize both vehicle-to-grid (V2G) operation and traction operation for EVs. The large capacitor is avoided in DC link of the proposed power conversion system. Instead, an active snubber with a small film capacitor is connected to the DC link to suppress the voltage oscillation, which is induced by removal of the large DC-link capacitor. By designing the phase shifting control for the primary H-bridge of DAB, a high-frequency pulsating DC-link voltage with zero portions is generated. Setting switching actions of the secondary H-bridge of DAB and TPFL during zero portions of DC-link, the zero-voltage-switching (ZVS) operation is achieved and the system efficiency can be improved consequently. Therefore, the fixed-switch-moment control strategies, namely the finite-set model-predictive-control (FS-MPC) and switch-table direct-torque-control (ST-DTC), are proposed to regulate TPFL for V2G operation mode and traction operation mode, respectively. Detailed analysis of different switch states within one half operating cycle is presented. Both simulation and experiment are conducted to verify the effectiveness of the proposed system and control schemes.

30 June 2020 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
WYWenfei Yu
Wenfei Yu
Wei HuaWei Hua
Wei Hua
JQJi Qi
Ji Qi
HZHengliang Zhang
Hengliang Zhang
Gan ZhangGan Zhang
Gan Zhang
GMGuangtong Ma
Guangtong Ma
Brushless modular spoke type permanent magnet (MSTPM) machine has exhibited prior electromagnetic performance over conventional surface-mounted PM machines for in-wheel traction system in electric vehicles (EVs). However, analysis of thermal behavior of MSTPM machines is rather insufficient, even accurate thermal analysis is of significant importance due to poor heat dissipation condition inside the wheel hub. Conventionally, the losses produced in electrical machines by EM prediction is equivalent to the heat source in normal thermal analysis, and only the resultant thermal behavior is investigated. However, the reaction of temperature rising on the EM performance is neglected. In this paper, a bi-directional coupled electromagnetic-thermal analysis method is proposed and carried out by a combination of lumped parameter thermal network (LPTN) model and finite element method (FEM), where both steady-state temperature distribution and transient-state temperature rise are investigated for MSTPM machines. By finite number of iterations between magnetic and thermal fields, the electromagnetic performance and thermal behavior can be predicted more accurately due to the coupling effect considered. The coupled model-predicted results are verified by 3D-FEM and experimental measurement, which shows that the proposed method has advantages in both computational efficiency and accuracy as well as can be applied to other electrical machines.

1 September 2021 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MLMingming Li
Mingming Li
Huafeng XiaoHuafeng Xiao
Huafeng Xiao
Ming ChengMing Cheng
Ming Cheng
For current-controlled grid-connected inverters with LCL filter, the essence of grid voltage full feedback is to improve the output impedance of grid-connected inverters to infinity, which can eliminate the influences of grid voltage distortion and the non-negligible grid impedance. However, existing full feedforward strategies are complex and control delay cannot be compensated precisely, which leads to the instability of system when the full feedforward of the voltage at the point of common coupling under the weak grid is adopted. This article first proposes a simplified full feedforward strategy based on grid-side inductor volt-age differential feedback active damping (GIVD-AD). Second, repetitive prediction (RP) is used to compensate for the control delay. Then, a virtual impedance branch is added and an adaptive algorithm for modifying virtual impedance based on the difference between predicted grid voltages by Newton interpolation prediction (NIP) and RP is proposed. With the proposed method, grid-connected inverters can work stably when grid impedance changes suddenly and exhibit strong rejection ability against grid-voltage harmonics. Finally, simulative and experimental results from a 3-kW single-phase grid-connected inverter are provided to prove the effectiveness of the proposed strategy.

4 March 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
MHMingjin Hu
Mingjin Hu
Wei HuaWei Hua
Wei Hua
ZWZheng Wu
Zheng Wu
NDNingyi DAI
Ningyi DAI
Huafeng XiaoHuafeng Xiao
Huafeng Xiao
Wei WangWei Wang
Wei Wang
Thermal drift-caused current measurement offset error usually results in unfavorable torque ripples of fundamental frequency, and hence a compensation method for current offset error is proposed in this paper, which is initially derived based on the non-salient-pole machines and then extended to the salient-pole machines. By filtering the difference between the predicted currents from a simple nominal model and the measured currents, the offset error is directly estimated and then compensated with minimal effects on the current dynamics. It is proved that the estimation is accurate if the filter has unity gain at the frequency of the offset error. Therefore, the proposed method is free of the current regulator type and shows strong robustness against machine parameter deviations. It can also stably work even when the output voltage is saturated. Two kinds of filters are designed in the stationary reference frame, and the low-pass filter with low bandwidth is recommended for its easy implementation. Finally, the effectiveness of the proposed method is verified by simulations and experiments.

1 April 2014 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
Huafeng XiaoHuafeng Xiao
Huafeng Xiao
XLXipu Liu
Xipu Liu
KLKe Lan
Ke Lan
The unipolar sinusoidal pulse width modulation (SPWM) full‐bridge inverter brings high‐frequency common‐mode voltage, which restricts its application in transformerless photovoltaic grid‐connected inverter. The freewheeling path added in ac side is adopted to restrict leakage current, but the common‐mode voltage is variable at switching frequency scale. To solve this problem, an improved full‐bridge structure with two switches and a capacitor divider has been proposed, which guarantees that freewheel path is clamped to half of input voltage in freewheel period. Sequentially, the high‐frequency common‐mode voltage has been avoided in unipolar SPWM full‐bridge inverter. The operation mode and the clamping mode are analysed, and several related topologies are discussed. Finally, the differential‐mode and common‐mode performance of the proposed topology are verified by a universal prototype inverter rated at 1 kW.