Yiyong Wu

Prof. Yiyong Wu


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2019 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
CYChunping Yang
Chunping Yang
JDJunjie Ding
Junjie Ding
JMJie Ma
Jie Ma
BZBiao Zhang
Biao Zhang
FYFeng Ye
Feng Ye
QLQiang Liu
Qiang Liu

1 December 2020 in Surface and Coatings Technology
Verified
Journal Article
Closed access
YWYou Wu
You Wu
DJDandan Ju
Dandan Ju
HWHao Wang
Hao Wang
HZHuiyang Zhao
Huiyang Zhao
CSChengyue Sun
Chengyue Sun
YWYi Wang
Yi Wang

29 October 2020 in RSC Advances
Verified
Journal Article
Open access
PDF file
DJDandan Ju
Dandan Ju
SCSun Chengyue
Sun Chengyue
WHWang Hao
Wang Hao
WXWang Xinmin
Wang Xinmin
YWYiyong Wu
Yiyong Wu
XQXuepeng Qiu
Xuepeng Qiu
Compared with the single irradiated sample, the tensile strength and elongation at break after the combination of proton irradiation and strain increased, indicating that introducing strain during irradiation will weaken the damage of irradiation.

1 August 2019 in Polymer Degradation and Stability
Verified
Journal Article
Closed access
LHLongyan Hou
Longyan Hou
YWYiyong Wu
Yiyong Wu
JXJingdong Xiao
Jingdong Xiao
BGBin Guo
Bin Guo
YZYingying Zong
Yingying Zong

28 November 2022 in Polymers
Verified
Journal Article
Open access
PDF file
IKIlya Kobykhno
Ilya Kobykhno
AKAndrey Kiryanov
Andrey Kiryanov
VV. Klinkov
V. Klinkov
ACAlla Chebotareva
Alla Chebotareva
Stanislav EvlashinStanislav Evlashin
Stanislav Evlashin
Oleg TolochkoOleg Tolochko
Oleg Tolochko
In this work, we studied the influence of the geometry and degree of filling of glass dispersed particles on the optical and mechanical properties of flexible high-transmission composites, based on thermoplastic polyurethane. Glass spheres, glass flake and milling glass fiber were used as fillers. Studies of mechanical properties have shown that the introduction of any filler leads to a decrease in tensile strength and an increase in the elastic modulus of the composite material, however, with the introduction of glass flakes and milling glass fiber, a significant increase in the yield strength of the material is observed. The optical properties of composites with glass spheres decrease exponentially with an increase in the volume fraction of the filler. With an increase in the concentration of glass flakes and milling glass fiber to 10 vol.%, a sharp decrease in transmission is observed. With a further increase in concentration, the orientation of the filler along the film occurs, due to which the transmission in the visible range increases to values close to those of a pure polymer.

29 May 2018 in Energy Science & Engineering
Verified
Journal Article
Open access
PDF file
GHGuo Hongliang
Guo Hongliang
YWYiyong Wu
Yiyong Wu
WJWang Jie
Wang Jie
GBGuo Bin
Guo Bin
XJXiao Jingdong
Xiao Jingdong
YHYu Hui
Yu Hui
Artifact is a special kind of phenomenon related to fluorescence coupling and shunt resistance in external quantum efficiency (EQE) measurements in multijunction (MJ) solar cells, and it is sensitive to the defects and damages. In this paper, the changes of artifacts were studied in partial irradiated MJ solar cells by common or two‐dimension mapping Quantum Efficiency (QE) measurements. Simplified mathematical models and graphic analysis were applied to explain the mechanisms of changes of artifacts. Irradiation weakens the artifacts effects due to the decrease in relative fluorescence yield. Artifacts analysis results indicate that after 1 MeV electron irradiation, the open circuit voltage Voc of GaInP subcell decays from 1.40 V to 1.35 V, and the reverse saturation non‐radiative recombination current I02 increases 3.7 times. Correspondingly, after 70 keV protons irradiation, the open circuit voltage Voc decays to 0.90 V and I02 increases 7550 times by EQE artifacts analysis. Lateral scanning of the partial damaged samples shows a smooth artifacts transition region that appears near the boundary of damaged region in MJ solar cells. This is found correlated with the difference in the lighted areas of bias light and EQE pulse spot. 2D artifacts analysis could properly explain the smoothness and shift of damage interface.