The present article addresses a generation of predictive models that assesses the thickness and length of internal defects in additive manufacturing materials. These modes use data from the application of active transient thermography numerical simulation. In this manner, the raised procedure is an ad-hoc hybrid method that integrates finite element simulation and machine learning models using different predictive feature sets and characteristics (i.e., regression, Gaussian regression, support vector machines, multilayer perceptron, and random forest). The performance results for each model were statistically analyzed, evaluated, and compared in terms of predictive performance, processing time, and outlier sensibility to facilitate the choice of a predictive method to obtain the thickness and length of an internal defect from thermographic monitoring. The best model to predictdefect thickness with six thermal features was interaction linear regression. To make predictive models for defect length and thickness, the best model was Gaussian process regression. However, models such as support vector machines also had significative advantages in terms of processing time and adequate performance for certain feature sets. In this way, the results showed that the predictive capability of some types of algorithms could allow for the detection and measurement of internal defects in materials produced by additive manufacturing using active thermography as a non-destructive test.
Dowel-type fasteners are one of the most used type of connections in timber joints. Its design follows the equations included in the Eurocode 5. The problem with these equations is that they do not adequately contemplate the resistive capacity increase of these joints, when using configurations which provoke the so-called rope effect. This effect appears when using threaded surface dowels instead of flat surface dowels, expansion kits or nut-washer fixings at the end of the dowel. The standards consider this increase through a constant value, which is a poor approximation, because it is clearly variable, depending on the joint displacement and because is much bigger, especially when using nut-washer fixings. It is also very important because of the rope effect trigger interesting mechanisms that avoids fragile failures without warning of the joints. For these reasons, it is essential to know how these configurations work, how they help the joint to resist the external loads and how much is the increase resistance capacity in relationship with the joint displacement. The methods used to address these issues consisted of a campaign of experimental tests using actual size specimens with flat surface dowels, threaded surface dowels and dowels with washer-nut fixings at their ends. The resistance capacity results obtained in all the cases has been compared with the values that will come using the equations in the standards. After the tests the specimens were cut to analyze the timber crushings, their widths, the positions and level of plasticizations suffer in the steel dowels and in the washer-nut fixings and the angle formed in the dowel plastic hinges. With all this information the failure mode suffered by the joints has been identified and compared with the ones that the standards predict. The results for the size materials and types of joints studied shows that the crush width average values go from 20 mm with flat surface dowels, to 24 mm in threaded to 32 mm in threaded with washer-nut fixings. The rope effect force/displacement goes from 100 N/m in threaded surface dowels to 500 N/m in threaded with washer-nut fixings. Finally, the load capacities are on average 290% higher those indicated in the standard. The main conclusion is that the rope effect force should be considered in the standards in more detail as a function of multiple variables, especially the displacement of the joint.
This paper provides a study of the mechanical energy distribution in dowel-type joints in timber structures when using expansive kits. The compression caused by the expansive kit increases the friction between the dowel and the timber’s hole, opposing the longitudinal sliding that occurs during the bending of the dowel. The ensuing rope effect increases the load capacity of the joint. The aim was to determine the advantages and disadvantages of using this kind of reinforcement. For this purpose, an ad hoc finite element model of the joint was prepared taking the contact between the different components of the joint into account and appropriately simulating the radial expansion of the dowel and the behavior of the timber. The model was checked for accuracy by comparing the results with those coming from a set of experimental tests. After that, the model was used to verify that the use of the expansive kit reinforcement leads to a slight improvement in the load capacity of the joint. This improvement is related to the frictional forces, whose effect is especially significant at low levels of joint displacement.
Este trabajo presenta un estudio de las tensiones que aparecen en una unión de tres barras, de una cercha ligera de madera, realizada con placas-clavo. El objetivo fue determinar el efecto de las variables más significativas, como el porcentaje de esfuerzo transmitido por contacto directo entre piezas que trabajan a compresión, el espesor de la placa, el nivel de cargas y el diseño de la unión. Para realizar el estudio, se desarrollaron modelos paramétricos de elementos finitos de la unión. Del análisis de los resultados, se concluye que existe un valor de la holgura entre piezas a partir del cual el contacto aparece, y otro por debajo del cual el porcentaje de la contribución de la transmisión de esfuerzo por contacto se estabiliza. También se observa que estos valores no se ven afectados por el espesor de la placa o el diseño de la unión.