The objective of this study is to investigate the mechanical properties and the composite action of circular concrete-filled steel tube (CFST) columns subjected to compression-torsion load using finite element model analysis. Load–strain (T–γ) curves, normal stress, shear stress, and the composite action between the steel tubes and the interior concrete were analyzed based on the verified 3D finite element models. The results indicate that with the increase of axial force, the maximum shear stress at the core concrete increased significantly, and the maximum shear stress of the steel tubes gradually decreased. Meanwhile, the torsional bearing capacity of the column increased at first and then decreased. The torque share in the columns changed from the tube-sharing domain to the concrete-sharing domain, while the axial force of the steel tube remained unchanged. Practical design equations for the torsional capacity of axially loaded circular CFST columns were proposed based on the parametric analysis. The accuracy and validity of the proposed equations were verified against the collected experimental results.
This paper presents an experimental and numerical study on large dimension concrete-filled square low steel ratio steel tubular (CFST) stub columns under axial loading. Four specimens were designed to investigate the effects of steel ratio on the confinement effect of square CFST stub columns with a low steel ratio. ABAQUS was used to establish 3D finite element (FE) models for simulation of square CFST stub columns with a low steel ratio under axial loading. Furthermore, based on the experimental verification, the definition of the confinement index (ϕ = fsAs/(fcAc)) was discussed and the effect of the grade of concrete and steel tube was also investigated. With the same cross-sectional dimensions, the confinement effect of the square CFST stub columns with a low steel ratio (less than 0.05) was better than the others. The stub columns with the yield strength of steel tube fs = 235 MPa (345, 420 MPa) and compressive cubic strength of concrete fcu = 40 MPa (60, 80 MPa) can give fully demonstrate the material performance and reflect the better confinement effect. Based on the experimental results and FE modeling, a practical calculation formula for the ultimate load-carrying capacity of square CFST stub columns with a low steel ratio was proposed. The formula calculation results presented in this paper show good agreement with the experimental results. Compared with the existing formulas, the proposed formula has better precision.
Existing experimental research on bond properties of the interface between Carbon Fiber Reinforced Polymer (CFRP) and damaged concrete is limited, although CFRP strengthening technology has been widely used for corroded reinforced concrete structures. This work investigated the bond behavior of CFRP to the corrosion-cracked concrete interface, in which three factors were considered for experimentation, including corrosion degree, concrete strength and concrete cover thickness. The tests were conducted by developing a self-balancing double shear lap test device. In addition, a corrosion scene was provided simultaneously to simulate the external corrosion environment. The results showed that three peeling modes of CFRP sheets were observed with respect to corrosion degrees of the steel bars. The effects of the three factors on the stripping bearing capacity and effective bond length of CFRP sheets were discussed by systematic parametric analysis. Finally, a nonlinear degenerate law of CFRP-to-concrete interface considering the corrosion degree was improved and verified in this study.
To study the evolution of mechanical properties of steel rebars in the China Railway Track System Type II (CRTS II) ballastless track–bridge structural system under repeated train loads, a 1/4 scale three-span ballastless slab track simple-supported bridge structural system specimen was manufactured and subjected to a multistage fatigue test with 18 million cycles. The experimental results show that the strain amplitude of the steel bar changes proportionally to the fatigue stress amplitude, and there is an obvious strain increase in the loading stage 4, where the fatigue stress amplitude is the largest. During the test, the cumulative strain–amplitude ratio first decreases then increases. At the end of the test, the cumulative strain–amplitude ratio increases by 5.46% and 5.32%, respectively, at L/2 and L/4 sections. The load–strain curve of the steel rebar keeps the shape of an oblique straight line. The slope increases first and then decreases with a degradation at the end of the test of 5.15% and 4.81%, respectively, at L/2 and L/4 sections. The mechanical properties of the rebar are enhanced under the first three million fatigue loading cycles: this is the fatigue strengthening stage. The mechanical properties of reinforcement gradually degrade from the three millionth cycle to the end of the test: this is the fatigue damage stage. Finally, based on the material fatigue damage model and the multistage cumulative damage criterion, the change rule of the load–strain curve slope of steel rebars in the fatigue damage stage is obtained by finite element simulation. The simulation results agree well with the experimental data, proving the validity of the calculation method proposed in this paper.
Due to the accumulated fatigue damage in steel–concrete continuous composite box beams, a plastic hinge forms in the negative moment zone, leading to significant internal force redistribution. To investigate the internal force redistribution in the negative moment zone and confirm structural safety under fatigue loading, experimental tests were conducted on nine steel–concrete continuous composite box beams: eight of them under fatigue testing, one of them under static testing. The test results showed that the moment modification coefficient at the middle support increases during the fatigue process. When approaching fatigue failure, an increase of 1.0% in the reinforcement ratio or 0.27% in the stirrup ratio results in a reduction of 13% in the moment modification coefficient. Furthermore, a quadratic function model was proposed to calculate the moment modification coefficient of a steel–concrete continuous composite box beam during the fatigue process, which exhibited good agreement with the experimental results. Finally, we verified the applicability of the plastic hinge rotation theory for steel–concrete continuous composite box beams under fatigue loading.