The U-shaped fiber configuration represents the elementary form of micro-displacement sensing, characterized by its exceptional freedom and flexibility. The study proposes the U-shaped bent single-mode–multimode–single-mode (SMS) fiber structure that integrates the multimode interference (MMI) effect for enhanced mode dispersion and the Mach–Zönder interference (MZI) effect for spectral sensitivity improvement. The transmission spectral properties of the U-shaped SMS fiber structure with a bent radius over 1 are experimentally measured as the change in displacement varied within the range of 5 in this work. As the radius decreases, the spectrum shows redshift, which is related to the central wavelength of the peak or dips—a smaller wavelength results in a stronger redshift for the same displacement change. The average sensitivity of micro-displacement measurement within a range of 5 is 5.41 , and the linearity is 99.62%. The maximum sensitivity of U-shaped SMS fiber structure is 34.46 , with the minimum displacement change of approximately 5.804 . The transmission spectral properties of the U-shaped SMS fiber structure within the ranges of 50 , 500 , and 5 mm are experimentally measured in this work. This experiment observed a relatively uniform spectral drift pattern in a large range of micro-displacement sensing. The measurement range is limited by the limited spectral range of the light source and the discontinuous variation in the effective refractive index. This provides an experimental reference for further understanding the characteristics of U-shaped fiber structures and applying its application in micro-displacement sensing.
The effect of the geometric parameters on the flow and heat transfer characteristics of a double-layer U-shape microchannel heat sink (DL-MCHS) for a high-power diode laser was investigated in this work. FLUENT 19.2 based on the finite volume method was employed to analyze the flow and heat transfer performance of DL-MCHS. A single variable approach was used to fully research the impact of different parameters (the number of channels, the channel cross-sectional shape, and the aspect ratio) on the temperature distribution, pressure drop, and thermal resistance of the DL-MCHS. The rectangular DL-MCHS heat transfer performance and pressure drop significantly increased with the rise in the channel’s aspect ratio due to there being a larger wet perimeter and convective heat transfer area. By comparing the thermal resistance of the DL-MCHS at the same power consumption, it was found that the rectangular DL-MCHS with an aspect ratio in the range of 5.1180–6.389 had the best overall performance. With the same cross-sectional area and hydraulic diameter (AC = 0.36 mm, Dh = 0.417 mm), the thermal resistance of the trapezoidal microchannel heat sink was 32.14% and 42.42% lower than that of the triangular and rectangular ones, respectively, under the condition that the pumping power (Wpp) was 0.2 W. Additionally, the thermal resistance was reduced with the increment of the number of channels inside the DL-MCHS, but this would induce an increased pressure drop. Thus, the channel number has an optimal range, which is between 50 and 80 for the heat sinks in this study. Our study served as a simulation foundation for the semiconductor laser double-layer U-shaped MCHS optimization method using geometric parameters.
1 January 2021 in Journal of Physics Communications
The pump spectral propriety of three types of commercial 915 and 976 nm LDs on single frequency Erbium-Ytterbium co-doped fiber amplifier (EYDFA) is theoretical and experimental analyzed. The slope efficiency, ASE intensity and linewidth broadening of the wavelength stabilized or un-stabilized LDs pumped amplifier are compared in detail. The results demonstrate that 976 nm LD pumping exhibits superior to 915 nm LD in efficiency and SNR. Comparing with wavelength stabilized 976 nm LD, the wavelength un-stabilized 976 nm LD with center wavelength deviating from Yb absorption peak and over 4 nm linewidth has better performance in Yb-ASE suppression but slightly lower in efficiency and linewidth broadening. The difference between the two 976 nm LDs could be taped off by increasing the seed power or output power. This work indicate that wavelength un-stabilized 976 nm LD is more suitable for pumping high power single-frequency EYDFA to avoid the bottlenecking effect, and provide reference for the optimal pump selection.
A liquid-sealed single-mode–no-core–single-mode (SNS) structure fiber temperature sensor based on polyvinyl alcohol (PVA) partial replacement coating is proposed. Using a liquid-sealed glass capillary structure, the PVA solution is introduced into the SNS structure and avoids its influence by environmental humidity. Temperature can be obtained by measuring the shift of the multimode interference spectrum, which is affected by the thermal optical effect of the PVA solution. Through theoretical simulation of the sensor, the optimal NCF fiber length and coating stripped length are obtained by comprehensively considering the transmitted loss and output spectrum signal-to-noise ratio (SNR). The optimal PVA solution concentration is selected by measuring the thermo-optic coefficient (TOC) and refractive index (RI). Based on the theoretical optimization results, a PVA solution-coated SNS fiber optic temperature sensor is experimentally fabricated, and temperature-sensing characteristics are measured within −3.6 to 73.2 °C. The experimental results show that the sensor has a high sensitivity (nm/°C, maximum is 21.713 nm/°C) and has a resolution of 10−3 °C. has a stable negative linear relationship with temperature, and the correlation coefficient of the fitting curve exceeds 95%. The temperature cycling experiment and long-term stability test show that the temperature sensor has good repeatability and stability. The experimental results also show the nonlinear relationship between the temperature measurement range and sensitivity, clarify the important factors affecting the response performance of fiber temperature sensors, and provide important reference values for optical fiber temperature sensors.
The ring cavity fiber laser with saturable absorption fibers is a simple and practical technical way of achieving single-frequency laser output. However, this structure cannot obtain wavelength-tunable laser output. In this work, an external injection locking signal launched by tunable LD is used to optimize the tunability in single-frequency ring cavity fiber lasers. By aligning the external injection signal, tunable laser output ranging from 1544.13 to 1546.51 nm is achieved. The maximum output is 16.5 mW and the linewidth is less than 6.15 kHz. The operation process and the linewidth compression effect of external Injection signals are investigated. The results indicate that there is a correlation between the output signal-to-noise ratio and the output linewidth, and this wavelength-tuning structure has the potential for rapid tuning. This work provides a technical solution for achieving a tunable single-frequency laser in the ring cavity structure.