To address the increasing demand for safe and effective treatment options for pelvic organ prolapse (POP) due to the worldwide ban of the traditional polypropylene meshes, this study introduced degradable polycaprolactone (PCL)/polyethylene glycol (PEG) composite meshes fabricated with melt-electrowriting (MEW). Two PCL/PEG mesh groups: 90:10 and 75:25 (PCL:PEG, wt%) were fabricated and characterized for their degradation rate and mechanical properties, with PCL meshes used as a control. The PCL/PEG composites showed controllable degradation rates by adjusting the PEG content and produced mechanical properties, such as maximal forces, that were higher than PCL alone. The antibacterial properties of the meshes were elicited by coating them with a commonly used antibiotic: azithromycin. Two dosage levels were used for the coating: 0.5 mg and 1 mg per mesh, and both dosage levels were found to be effective in suppressing the growth of S. aureus bacteria. The biocompatibility of the meshes was assessed using human immortalized adipose derived mesenchymal stem cells (hMSC). In vitro assays were used to assess the cell viability (LIVE/DEAD assay), cell metabolic activity (alamarBlue assay) and cell morphology on the meshes (fluorescent and electron microscopy). The cell attachment was found to decrease with increased PEG content. The freshly drug-coated meshes showed signs of cytotoxicity during the cell study process. However, when pre-released for 14 days in phosphate buffered saline, the initial delay in cell attachment on the drug-coated mesh groups showed full recovery at the 14-day cell culture time point. These results indicated that the PCL/PEG meshes with antibiotics coating will be an effective anti-infectious device when first implanted into the patients, and, after about 2 weeks of drug release, the mesh will be supporting cell attachment and proliferation. These meshes demonstrated a potential effective treatment option for POP that may circumvent the issues related to the traditional polypropylene meshes.

Introduction: Prostate-specific membrane antigen positron emission tomography/computed tomography (PSMA PET/CT), in combination with magnetic resonance imaging (MRI), may enhance the diagnosis and staging of prostate cancer. Image fusion of separately acquired PET/CT and MRI images serve to facilitate clinical integration and treatment planning. This study aimed to investigate different PSMA PET/CT and MRI image fusion workflows for prostate cancer visualisation. Methods: Eighteen patients with prostate cancer who underwent PSMA PET/CT and MRI prior to radical prostatectomy were retrospectively selected. Alignment of the prostate was performed between PET/CT and MRI via three techniques: semi-automatic rigid, automatic rigid, and automatic non-rigid. Image fusion accuracy was evaluated through boundary and volume agreement, quantified by the Dice Similarity Coefficient (DSC), 95% Hausdorff Distance (HD), and Mean Surface Distance (MSD), with comparison against reconstructed histopathology slices. Results: Image fusion using all techniques resulted in clear lesion visualisation from PSMA PET/CT overlay and anatomical detail afforded by the MRI base and was consistent with histopathology tumour location. Image fusion accuracy was within the recommended range based on a DSC of 0.8–0.9. The automatic non-rigid registration method had the highest volume agreement (DSC: 0.96 ± <0.01) and boundary agreement (HD: 1.17 ± 0.35 mm) when compared to automatic rigid (DSC 0.88 ± 0.02, HD 3.18 ± 0.29 mm) and semi-automatic rigid (DSC 0.80 ± 0.06, HD 5.25 ± 1.68 mm). Conclusions: Image fusion of clinically obtained PET/CT and MRI is feasible and clinically acceptable for use in prostate cancer diagnosis and surgical management. While the best accuracy was observed with the automatic non-rigid technique, which requires further validation, image fusion with clinically accessible methods (semi-automatic rigid) may currently aid patient education, pre-operative planning, and intra-operative guidance.

In contrast to other additive manufacturing methods such as Wire Arc Additive Manufacturing or Laser Metal Deposition, the cold spray system designed by SPEE3D allows for structures to be printed at much lower temperatures. As a result, structures printed via cold spray often undergo post processing heat treatments that potentially alter the distribution of trace elements throughout the sample. The distribution of elements within these structures may then have a direct impact on the corrosion properties of these materials. The impact of post processing heat treatment parameters on the microstructure and distribution of Mg and Si trace elements within an Al alloy was investigated using cross section analysis of samples by SEM-EDS. From an Al-powered feedstock, alloys were printed using SPEED3D’s LightSPEE3D printer utilising air as the carrier gas, at 30 Bar and 500 °C; various post processing heat and water quench treatments were then applied. The results revealed a reorganisation of Mg (which subsequently becomes oxidised) toward the edges of pores, regions that typically have a higher surface energy. This is in direct contrast to the largely homogenous distribution of Mg in the samples that did not undergo post printing heat treatments. The addition of charcoal during the heat treatment process also resulted in the redistribution of Si within the sample, and the creation of silicon carbide structures. The impact of the reorganisation of Mg within the sample as well as the creation of silicon carbide structures on the selective corrosion of these materials was then investigated using potentiodynamic corrosion testing and electrochemical impedance spectroscopy.