The proper disposal of steel slag has always been a great challenge for the metallurgical industry in China and around the world. In this work, the steel slag aggregate (SSA) was surface pretreated (PSSA) and applied into asphalt mixture. The adhesive behavior between the bitumen and five different types of aggregates (i.e., limestone, diorite, diabase, SSA, PSSA) were evaluated based on the contact angle and binder bond strength tests. The pavement performance of three asphalt mixtures which contain normal aggregate, SSA and PSSA respectively, was analyzed by Marshall stability test, wheel-tracking rutting test, low-temperature bending creep test and water sensitivity test. The results showed that surface modification can improve the surface properties of SSA, reduce its contact angle with bitumen, and eventually lead to the improvement of adhesion between them. In addition to the satisfied low-temperature properties, PSSA was found to significantly improve the anti-rutting property and reduce the water sensitivity of asphalt mixture. This work is expected to promote an alternative application for recycling of SSA in pavement engineering.
To reduce vehicle exhaust gas pollution in transport-intensive roadways and tunnels, six types of photocatalytic asphalt binders were designed using graphite-phase carbon nitride (g-C3N4) and nanoscale titanium dioxide (nano-TiO2) particles. In this paper, the rheological behaviors and fatigue life of the nano-TiO2-modified asphalt binder (TiO2-MA) and g-C3N4-modified asphalt binder (C3N4-MA) were investigated. NO degradation capacity of six types of photocatalytic asphalt binders was characterized under visible light conditions. The results showed that TiO2-MA had more excellent rheological behaviors and rutting resistance than C3N4-MA. In addition, 4 wt% nano-TiO2 markedly improved the rheological behaviors and rutting resistance of MA compared to other dosages. TiO2-MA exhibited higher fatigue resistance. The fatigue life of TiO2-MA with 4 wt% nano-TiO2 was increased to 234.1% at 2.5% strain and 242.5% at 5% strain, respectively, compared to base asphalt binder (BA). C3N4-MA had better NO degradation capacity than TiO2-MA. Meanwhile, the NO degradation efficiency of C3N4-MA reached 17.8% with 5 wt% g-C3N4.
1 November 2020 in JOURNAL OF SHENZHEN UNIVERSITY SCIENCE AND ENGINEERING
In order to use the solid and liquid waste resources to improve performances of base asphalt, waste frying oil (WFO) and crumb rubber (CR) are used to modify the asphalt to obtain the sustainable pavement material. The molecular structures and the performances of the modified asphalts with different amounts of WFO and CR are analyzed by conventional asphalt methods, short-term aging test and Fourier transform infrared spectroscopy (FT-IR). The results indicate that the retained penetration ratio (RPR), the softening point increment (SPI) and retained ductility ratio (RDR) indexes of modified asphalts with different amounts of WFO-CR composite are better than those of the base asphalt after short-term aging test. WFO and CR can improve anti-aging performance. Moreover, FT-IR results show that the absorption peaks at 814 cm-1 and 720 cm-1, which represent the alkenyl or benzene ring CC in WFO-CR composite modified asphalt after short-term aging, increase obviously. Both the carbonyl absorption peak and the sulfoxide absorption peak are improved for modified asphalts with different amounts of WFO-CR composite. The quantitative analysis shows that the carbonyl and sulfoxide indices of the modified asphalt reach the lowest values with 5.0% WFO and 20.0% CR, which are 36.02% and 32.04% lower than those of the base asphalt, respectively.
In order to explore the feasibility and efficacy of reed-fiber-modified bitumen (RFMB), three lengths and three dosages of reed fibers were selected to modify bitumen and bituminous mortar, while the physicochemical properties of RFMB and RFMB mortar were analyzed. In this work, FTIR spectroscopy was employed to characterize the chemical impact of fiber on bitumen. The viscidity and rheology of RFMB and the tensile strength of RFMB mortar were evaluated using a Brookfield viscometer, dynamic shear rheometer, and monotonic tensile test. The results showed that adding fibers primarily affects the physical structure rather than the chemical composition of bitumen, confirmed by FTIR spectroscopy. RFMB viscosity increased with higher fiber dosage and fiber length. Rheological evaluations showed an enhanced complex shear modulus for RFMB, suggesting improved performance at higher temperatures but increased stiffness at lower temperatures, with the latter indicating reduced flexibility. RFMB also demonstrated superior fatigue and rutting resistance, albeit with compromised stress sensitivity. Tensile tests on RFMB mortar highlighted significant improvements, especially with longer fibers, while shorter 0.4 mm fibers showed modest reinforcement effects, possibly due to uneven distribution during sample preparation.