Friction and very high temperature are still the major challenges in hard machining technology and they greatly affect cutting efficiency. The application of the MQL (minimum quantity lubrication) method, using nanoparticles in order to improve the cooling lubrication performance of the base cutting oil, has proven to be a promising solution. Hence, this work aimed to investigate the effectiveness of Al2O3/MoS2 hybrid nanofluid and Al2O3 and MoS2 mono nanofluids in the hard turning of 90CrSi steel (60–62 HRC) under an MQL environment. The Box-Behnken experimental design was used for three input variables, including nanoparticle concentration, air pressure, and air flow rate. Their influences on surface roughness and cutting forces were studied. According to the obtained results, it was shown that the application of hybrid nano cutting oils in MQL contributes to achieving better hard machining performance than the use of mono nanofluids. In particular, a lower cutting temperature is reported and the values of surface roughness Ra, back force Fp, and cutting force Fc were smaller and more stable under Al2O3/MoS2 hybrid nanofluid MQL than those under Al2O3 and MoS2 mono nanofluid MQL due to an improvement in cooling lubrication characteristics. Thus, this work provides a novel approach to study hybrid nanofluids for MQL hard machining.
Cutting fluids used in the metal machining industry have exerted serious impacts on the environment and human health. In addition, the very high cutting heat and forces in machining-hardened steels have been a growing concern in the metal cutting field. Hence, new, eco-friendly cooling and lubricating techniques are necessary to study and develop. Minimum quantity lubrication (MQL) and minimum quantity cooling lubrication (MQCL) using nano cutting fluids have been proven as alternative solutions for machining difficult-to cut materials while retaining an environmentally friendly characteristic. Accordingly, this paper aims to analyze and evaluate the hard turning efficiency of 90CrSi (60 ÷ 62 HRC) steel using MQL and MQCL conditions, using Al2O3 and MoS2 nano cutting fluids. The 2k-p experimental design and analysis of variance (ANOVA) were used to study the influence of input parameters including fluid type, lubrication method, nanoparticle type, nanoparticle concentration, cutting speed and feed rate on surface roughness. The obtained results showed that the machinability of CNMG120404 TM T9125 carbide tools was improved and the highest machinable hardness was increased from 35 HRC to 60 ÷ 62 HRC (rising by approximately 71.4 ÷ 77.1%) by using the nanofluid MQL and MQCL methods. Furthermore, MQCL gives better performance than MQL, and the Al2O3 nanofluid exhibits the better result in terms of surface roughness values than the MoS2 nanofluid. Feed rate displays the strongest influence on surface roughness, while fluid type, nanoparticle concentration and cutting speed show low impacts. From these results, technical guidance will be provided for further studies using Al2O3 and MoS2 nano cutting fluids for MQL and MQCL methods, as well as their application in machining practice.
Minimum quantity lubrication (MQL) has gained significant attention in various research fields and industrial applications for its advantages of being environmentally friendly and suitable for sustainable production. The effectiveness of MQL is increasing significantly by using nano cutting fluid, which can be produced by suspending nanoparticles in the based cutting fluid. This study aims to investigate the effects of MoS2 nanoparticle concentration, cutting speed, and feed rate on MQL hard turning of 90CrSi steel in terms of surface roughness and surface microstructure. The Box–Behnken experimental design was used to analyze the influence of input parameters and their interaction effects as well as to find the optimal set of variables. The obtained results prove the improvement of the machinability of carbide tools due to higher cooling and lubricating performance created by MoS2 nanofluid MQL, which contributes to improve the surface quality and reduce the manufacturing cost. There is an interaction effect between nanoparticle concentration and feed rate which has a strong influence on surface roughness.
Lubrication and cooling in hard machining is an urgent and growing concern. The use of a suitable cooling lubrication condition is a crucial factor and has a great influence on the machining efficiency and the machined surface quality in hard machining. Among the proposed technological solutions, minimum quantity lubrication (MQL) using nano-cutting oils is a novel solution and its effectiveness has been proven for hard turning. This work aims to investigate the influence of MQL technological parameters using MoS2 nano-cutting oil including nanoparticle concentration, air pressure, and air flow rate on surface roughness and the resultant cutting force in hard turning using CBN inserts. Box-Behnken optimal experimental design and ANOVA analysis were used to study the influence of the input parameters and determine the optimal values. The results present the influence of the survey parameters and provide technological guides for specific objective functions for further sustainable studies on MQL hard turning using nano-cutting oil.