Sarah Johanna Hirsch

Mrs. Sarah Johanna Hirsch

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
SHSarah Johanna Hirsch
Sarah Johanna Hirsch
LWLisa Winter
Lisa Winter
Thomas GrundThomas Grund
Thomas Grund
Thomas LampkeThomas Lampke
Thomas Lampke
In this study, an attempt was made to improve the mechanical properties and in particular the strength of a precipitation-hardenable aluminum alloy while still maintaining high ductility. For this purpose, AlSi7Mg0.6 (A357) powder with an average particle diameter of d50 = 40 µm was consolidated using field assisted sintering technique (FAST), and two material conditions were compared: an as-sintered and an underaging heat treated condition (T61). Mechanical properties were determined using tensile tests and hardness measurements. In addition, the microstructure was investigated by optical microscopy. Further, porosity and density were analyzed after the different heat treatments. By the underaging heat treatment, the surface hardness was increased by 100% and the yield strength was increased by 80% compared to the as-sintered material. However, the elongation to failure dropped to one third of that of the as-sintered material. Presumably, this effect was a result of an increased porosity due to the heat treatment. It is assumed that the observed pores were generated by artefacts from the FAST process used to manufacture the samples. The internal gas pressure and equilibrium diffusion supported by heat treatment temperature, and the reduction in surface energy caused by coalescent micropores, led to the enlargement of previously undetectable inhomogeneities in the as-sintered material that resulted in pores in the heat-treated sintered alloy.

28 March 2024 in Crystals
Verified
Journal Article
Open access
PDF file
SHSarah Johanna Hirsch
Sarah Johanna Hirsch
Nadja BerndtNadja Berndt
Nadja Berndt
Thomas GrundThomas Grund
Thomas Grund
Thomas LampkeThomas Lampke
Thomas Lampke
Solid state sintering of cast aluminum powders by resistance heating sintering (RHS), also known as spark plasma sintering or field-assisted sintering technique, creates a very fine microstructure in the bulk material. This leads to high performance material properties with an improved strength and ductility compared to conventional production routes of the same alloys. In this study, the mechanical behavior of an RHS-sintered age-hardenable A357 (AlSi7Mg0.6) cast alloy and a SiCp/A357 aluminum matrix composite (AMC) was investigated. Aiming for high strength and good wear behavior in tribological applications, the AMC was reinforced with a high particle content (35 vol.%) of a coarse particle fraction (d50 = 21 µm). Afterwards, separated and combined effects of particle reinforcement and heat treatment were studied under compressive load both at room temperature and at 350 °C. At room temperature compression, the strengthening effect of precipitation hardening was about twice as high as that for the particle reinforcement, despite the high particle content. At elevated temperatures, the compressive deformation behavior was characterized by simultaneously occurring temperature-activated recovery, recrystallisation and precipitation processes. The occurrence and interaction of these processes was significantly affected by the initial material condition. Moreover, a rearrangement of the SiC reinforcement particles was detected after hot deformation. This rearrangement lead to a homogenized dispersion of the reinforcement phase without considerable particle fragmentation, which offers the potential for secondary thermo-mechanical processing of highly reinforced AMCs.

17 May 2023 in Crystals
Verified
Journal Article
Open access
PDF file
SHSarah Johanna Hirsch
Sarah Johanna Hirsch
Thomas GrundThomas Grund
Thomas Grund
Thomas LampkeThomas Lampke
Thomas Lampke
Particle-reinforced aluminium matrix composites (AMC) with a high-volume fraction of ceramic reinforcement (>30 vol.%) combine high specific strength and stiffness with good wear resistance and thermal stability, resulting in their increasing popularity in high-load applications, such as brake discs and bearings. It is hence assumed that AMC will accumulate as scrap in the near future. Appropriate recycling strategies must therefore be developed to maintain AMC’s inherent properties. Melt-metallurgical recycling routes bear the danger of dissolving the ceramic reinforcement in the liquid metallic matrix and contaminating primary melts or forming intermetallic phases in secondary melts. Here, a solid-state AMC recycling route with crushing and sintering is investigated, wherein all steps are carried out below the solidification temperature of the aluminium matrix. A sintered primary AMC is mechanically converted into a particulate/powdery secondary raw AMC in coarse, medium, and milled quality (i.e., with d ≈ 7–12 mm, d ≈ 3–7 mm, and d < 300 µm) and subsequently resistance heating sintered to a secondary AMC under a variation of the sintering pressure. The two AMC generations are analysed and discussed regarding their microstructure and mechanical properties. Since the secondary AMC show reduced the mechanical strength, the fracture surfaces are analysed, revealing iron contaminations from the mechanical processing.

Verified
Journal Article
Open access
PDF file
PEPatrick Eiselt
Patrick Eiselt
SHSarah Johanna Hirsch
Sarah Johanna Hirsch
IOIsmail Ozdemir
Ismail Ozdemir
ANAndreas Nestler
Andreas Nestler
Thomas GrundThomas Grund
Thomas Grund
Thomas LampkeThomas Lampke
Thomas Lampke
Aluminium matrix composites (AMCs) represent an important group of high-performance materials. Due to their specific strength and a high thermal conductivity, these composites have been considered for the large-scale production of brake discs. However, preconditioning the friction surfaces is necessary to avoid severe wear of both the brake discs and the brake linings. This can be achieved through controlled friction against commercially available brake-lining materials and the formation of transfer or reactive layers (tribosurfaces). Homogeneous tribosurfaces allow for nearly wear-free brake systems under moderate brake conditions. In this work, preconditioning was carried out with a pin-on-disc tester, aiming for the fast creation of homogeneously formed and stable tribosurfaces. The influence of surface microedges perpendicular to the direction of friction on the machined AMC surfaces on the build-up speed and homogeneity of the tribosurfaces was investigated. The microedges were generated using ultrasonic-vibration-superimposed face turning. Thereby, the vibration direction corresponded to the direction of the passive force. For research purposes, the distance of the microedges was changed by varying the cutting speed and feed. The experiments were carried out using AMC disc specimens with a reinforcement content of a 35% volume proportion of silicon carbide particles. Machining was realised with CVD-diamond-tipped indexable inserts. The evaluation of the generated surfaces before and after preconditioning was achieved using 3D laser scanning microscopy and scanning electron microscopy. It was demonstrated that ultrasonic-vibration-superimposed face turning effectively generated microedges on the AMC surfaces. The results show that larger distances between the microedges enhanced the formation of stable tribosurfaces. Thus, the tribosystem’s steady state was reached quickly. Therefore, the benefits of AMC-friction-surface microstructuring on the generation of tribosurfaces under laboratory conditions were proven. These findings contribute to the development of high-performance AMC brake systems.

21 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
SHSarah Johanna Hirsch
Sarah Johanna Hirsch
PEPatrick Eiselt
Patrick Eiselt
IOIsmail Ozdemir
Ismail Ozdemir
Thomas GrundThomas Grund
Thomas Grund
ANAndreas Nestler
Andreas Nestler
ASAndreas Schubert
Andreas Schubert
AlSi7Mg/SiCp aluminium matrix composites (AMCs) with a high ceramic content (35 vol.%) that were produced by using the field-assisted sintering technique (FAST) were subjected to tribological preconditioning and evaluated as a potential lightweight material to substitute grey cast iron brake discs. However, since an uncontrolled running-in process of the AMC surface can lead to severe wear and thus to failure of the friction system, AMC surfaces cannot be used directly after finishing and have to be preconditioned. A defined generation of a tribologically conditioned surface (tribosurface) is necessary, as was the aim in this study. To simulate tribological conditions in automotive brake systems, the prepared AMC samples were tested in a pin-on-disc configuration against conventional brake lining material under dry sliding conditions. The influence of the surface topography generated by face turning using different indexable inserts and feeds or an additional plasma electrolytic treatment was investigated at varied test pressures and sliding distances. The results showed that the coefficient of friction remained nearly constant when the set pressure was reached, whereas the initial topography of the samples studied by SEM varied substantially. A novel approach based on analysing the material ratio determined by 3D surface measurement was developed in order to obtain quantitative findings for industrial application.