Polyyne and cumulene of infinite length as the typical covalent one-dimensional (1D) monatomic linear chains of carbon have been demonstrated to be metallic and semiconductor (Eg = 1.859 eV), respectively, by first-principles calculations. Comparing with single-walled carbon nanotubes, the densities are evidently low and the thermodynamic properties are similar below room temperature but much different at the high temperature range. Polyyne possesses a Young's modulus as high as 1.304 TPa, which means it is even much stiffer than carbon nanotubes and to be the superlative strong 1D material along the axial direction. The Young's modulus of cumulene is estimated to be 760.78 GPa. In addition, polyyne is predicted to be as a one-dimensional electronic material with very high mobility.

Post-traumatic peritendinous adhesion presents a significant challenge in clinical medicine. This study proposes the use of diamond-like carbon (DLC) deposited on polylactic acid (PLA) membranes as a biophysical mechanism for anti-adhesion barrier to encase ruptured tendons in tendon-injured rats. The results indicate that PLA/DLC composite membrane exhibits more efficient anti-adhesion effect than PLA membrane, with histological score decreasing from 3.12 ± 0.27 to 2.20 ± 0.22 and anti-adhesion effectiveness increasing from 21.61% to 44.72%. Mechanistically, the abundant C=O bond functional groups on the surface of DLC can reduce reactive oxygen species level effectively; thus, the phosphorylation of NF-κB and M1 polarization of macrophages are inhibited. Consequently, excessive inflammatory response augmented by M1 macrophage-originated cytokines including interleukin-6 (IL-6), interleukin-1β (IL-1β), and tumor necrosis factor-α (TNF-α) is largely reduced. For biocompatibility evaluation, PLA/DLC membrane is slowly absorbed within tissue and displays prolonged barrier effects compared to traditional PLA membranes. Further studies show the DLC depositing decelerates the release of degradation product lactic acid and its induction of macrophage M2 polarization by interfering esterase and PLA ester bonds, which further delays the fibrosis process. It was found that the PLA/DLC membrane possess an efficient biophysical mechanism for treatment of peritendinous adhesion.

The structure of liquid water is primarily composed of three-dimensional networks of water clusters formed by hydrogen bonds, and dissolved oxygen is one of the most important indicators for assessing water quality. In this work, distilled water with different concentration of dissolved oxygen were prepared, and a clear negative correlation between the size of water clusters and dissolved oxygen concentration was observed. Besides, a phenomenon of rapid absorption and release of oxygen at the water interfaces was unveiled, suggesting that oxygen molecules predominantly exist at the interfaces of water clusters. Oxygen molecules can move rapidly through the interfaces among water clusters, allowing dissolved oxygen to quickly reach a saturation level at certain partial pressure of oxygen and temperature. Further exploration into the mechanism by molecular dynamics simulations of oxygen and water clusters found that oxygen molecules can only exist stably at the interfaces among water clusters. A semi-empirical formula relating the average number of water molecules in a cluster (n) to ¹⁷O NMR half-peak width (W) was summarized: n = 0.1 W + 0.85. These findings provide a foundation for exploring the structure and properties of water.

The wide utilization of lithium-ion batteries (LIBs) prompts extensive research on the anode materials with large capacity and excellent stability. Despite the attractive electrochemical properties of pure Si anodes outperforming other Si-based materials, its unsafety caused by huge volumetric expansion is commonly admitted. Silicon monoxide (SiO) anode is advantageous in mild volume fluctuation, and would be a proper alternative if the low initial columbic efficiency and conductivity can be ameliorated. Herein, a hybrid structure composed of active material SiO particles and carbon nanofibers (SiO/CNFs) is proposed as a solution. CNFs, through electrospun processes, serve as a conductive skeleton for SiO nanoparticles and enable SiO nanoparticles to be uniformly embedded in. As a result, the SiO/CNF electrochemical performance reaches a peak at 20% the mass ratio of SiO, where the retention rate reaches 73.9% after 400 cycles at a current density of 100 mA g⁻¹, and the discharge capacity after stabilization and 100 cycles are 1.47 and 1.84 times higher than that of pure SiO, respectively. A fast lithium-ion transport rate during cycling is also demonstrated as the corresponding diffusion coefficient of the SiO/CNF reaches ~8 × 10⁻¹⁵ cm² s⁻¹. This SiO/CNF hybrid structure provides a flexible and cost-effective solution for LIBs and sheds light on alternative anode choices for industrial battery assembly.

We employ first-principles density functional theory calculations to study the surface reconstruction, energetic stability, and electronic structure of diamond C(331) surface. Spontaneous formation of graphene-like stripes on the reconstructed surface is found to occur as the surface terrace C atoms transform from sp ³ to sp ² hybridization upon structural relaxation. The comparison of the calculated absolute surface energies of C(331), C(111), and C(110) surfaces demonstrates the energetic stability of the graphitic-like C(331) surface. Local density of electronic states analysis reveals the occurrence of localized electronic states near the Fermi level, which may have a significant impact on the surface conductivity.

In the current highly industrialized living environment, air quality has become an increasing public health concern. Natural environments like forests have excellent air quality due to high concentrations of negative oxygen ions originating from low-voltage ionization, without harmful ozone. Traditional negative oxygen ion generators require high voltage for corona discharge to produce ions. However, high voltage can increase electron collisions and excitations, leading to more dissociation and recombination of oxygen molecules and consequently higher ozone production. To address the challenge of generating negative oxygen ions without accompanying ozone production, this study designed and constructed a low-voltage negative oxygen ion generator based on nanometer-tip carbon fiber electrodes. The advantage of this device lies in the high curvature radius of carbon fibers, which provides high local electric field strength. This allows for efficient production of negative oxygen ions at low operating voltages without generating ozone. Experiments demonstrated that the device can efficiently generate negative oxygen ions at a working voltage as low as 2.16 kV, 28% lower than the lowest voltage reported in similar studies. The purification device manufactured in this study had a total decay constant for PM_2.5 purification of 0.8967 min⁻¹ within five minutes, compared to a natural decay constant of only 0.0438 min⁻¹, resulting in a calculated Clean Air Delivery Rate (CADR) of 0.1535 m³/min. Within half an hour, concentrations of PM_2.5, PM₁, PM₁₀, formaldehyde, and TVOC were reduced by 99.09%, 99.40%, 99.37%, 94.39%, and 99.35%, respectively, demonstrating good decay constants and CADR. These findings confirm its effectiveness in improving indoor air quality, highlighting its significant application value in air purification.