High temperature measurement of the rotating parts in aero-engine system requires wireless passive sensors. Surface acoustic wave (SAW) devices capable of measuring high temperature wirelessly are therefore ideal for these extreme scenarios where wired sensors are not applicable. In this article, SAW sensors built on the LiNbO ₃ substrate which can measure up to 1100 °C with a good repeatability and endurance are reported. The platinum IDT and LiNbO ₃ substrate were effectively protected by a SiO ₂ passivation layer to ensure the functionality and stability of the SAW devices under extremely high temperature. Distinct linearity of f ₀ vs. temperature, together with the temperature durability of the SAW sensors were verified by conducting various high-temperature RF tests. Such a SAW sensor attached with an embedded near-field antenna was also formulated to enhance the wireless transmission quality for future high-temperature remote sensing system.

In the current highly industrialized living environment, air quality has become an increasing public health concern. Natural environments like forests have excellent air quality due to high concentrations of negative oxygen ions originating from low-voltage ionization, without harmful ozone. Traditional negative oxygen ion generators require high voltage for corona discharge to produce ions. However, high voltage can increase electron collisions and excitations, leading to more dissociation and recombination of oxygen molecules and consequently higher ozone production. To address the challenge of generating negative oxygen ions without accompanying ozone production, this study designed and constructed a low-voltage negative oxygen ion generator based on nanometer-tip carbon fiber electrodes. The advantage of this device lies in the high curvature radius of carbon fibers, which provides high local electric field strength. This allows for efficient production of negative oxygen ions at low operating voltages without generating ozone. Experiments demonstrated that the device can efficiently generate negative oxygen ions at a working voltage as low as 2.16 kV, 28% lower than the lowest voltage reported in similar studies. The purification device manufactured in this study had a total decay constant for PM_2.5 purification of 0.8967 min⁻¹ within five minutes, compared to a natural decay constant of only 0.0438 min⁻¹, resulting in a calculated Clean Air Delivery Rate (CADR) of 0.1535 m³/min. Within half an hour, concentrations of PM_2.5, PM₁, PM₁₀, formaldehyde, and TVOC were reduced by 99.09%, 99.40%, 99.37%, 94.39%, and 99.35%, respectively, demonstrating good decay constants and CADR. These findings confirm its effectiveness in improving indoor air quality, highlighting its significant application value in air purification.

Advances in radar technology have driven efforts to develop effective countermeasures. Plasma is recognized as a highly effective medium for absorbing electromagnetic waves. Recent research has focused on enhancing plasma element performance. This paper achieved ultra-high-density, low-pressure cold plasma with a density of 1.15 × 10¹² cm⁻³, surpassing similar studies by more than an order of magnitude. Tungsten electrodes with high-curvature spiked structures were invented to replace traditional iron–nickel alloy electrodes, increasing plasma density by 88.2% under the same conditions. Lightweight and cost-effective tubular and annular ultra-high-density, low-pressure cold plasma devices were developed, demonstrating exceptional performance in electromagnetic wave absorption, plasma transient antennas, and radar stealth technology. The influence of plasma on electromagnetic waves and its numerical relationship were analyzed. By measuring the radar cross-section (RCS), the reduction in radar detection rates was quantified. The results show that the ultra-high-density cold plasma devices exhibit very low intrinsic RCS values, suitable for plasma antenna applications. The array of plasma elements generates a large-area high-density low-pressure cold plasma. This plasma effectively reduces the radar cross-section (RCS) of metallic equipment in the S and C bands and shows attenuation in the X band. These effects highlight the superior characteristics of plasma technology in electronic warfare. This exploratory research lays the groundwork for further defense applications.

Rapid urbanization and industrialization have heightened concerns about air quality worldwide. Conventional air purification methods, reliant on chemicals or energy-intensive processes, fall short in open spaces and in combating emerging pollutants. Addressing these limitations, this study presents a novel water-film air purification prototype leveraging the adhesion between low-curvature liquid surfaces and air convection friction. Uniquely designed, this prototype effectively targets toxic gases (e.g., formaldehyde, SO₂, NO₂) and particulate matter (such as PM_2.5) while allowing continuous airflow. This research explores the adhesion and sedimentation capabilities of a low-curvature water solution surface under convection friction, reducing the surface energy to remove airborne pollutants efficiently. The prototype was able to reduce the initial concentration in a 30 m³ chamber within 180 min by 91% for formaldehyde, 78% for nitrogen dioxide (NO₂), 99% for sulfur dioxide (SO₂), and 96% for PM_2.5. Experimentally validated indicators—decay constants, CADR, and purification efficiency—enable a comprehensive evaluation of the purification device, demonstrating its efficacy in mitigating air pollution. This innovative design, which is cost-effective due to its use of easily accessible components and water as the primary medium, indicates strong potential for large-scale deployment. This study points to an environmentally friendly and economical approach to air purification, shedding light on a promising direction for enhancing indoor air quality. Further optimization and exploration of diverse pollutants and environmental conditions will propel the practical applications of this pioneering technology.