David Gibus

Dr. David Gibus

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2022 in Smart Materials and Structures
Verified
Journal Article
Closed access
AMAdrien Morel
Adrien Morel
LCLudovic Charleux
Ludovic Charleux
QDQuentin Demouron
Quentin Demouron
ABAya Benhemou
Aya Benhemou
DGDavid Gibus
David Gibus
ABAdrien Badel
Adrien Badel
In order to scavenge the energy of ambient vibrations, bistable vibration energy harvesters constitute a promising solution due to their large frequency bandwidth. Because of their complex dynamics, simple models that easily explain and predict the behavior of such harvesters are missing from the literature. To tackle this issue, this paper derives simple analytical closed-form models of the characteristics of bistable energy harvesters (e.g. power-frequency response, displacement response, cut-off frequency of the interwell motion) by mean of truncated harmonic balance methods. Measurements on a bistable piezoelectric energy harvester illustrate that the proposed analytical models allow the prediction of the mechanical displacement and harvested power, with a relative error below 10%. From these models, the influences of various parameters such as the inertial mass, the acceleration amplitude, the electromechanical coupling, and the resistive load, are derived, analyzed and discussed. The proposed models and analysis give an intuitive understanding of the dynamics of bistable vibration energy harvesters, and can be exploited for their design and optimization.

9 November 2022 in Smart Materials and Structures
Verified
Journal Article
Closed access
DGDavid Gibus
David Gibus
AMAdrien Morel
Adrien Morel
PGPierre Gasnier
Pierre Gasnier
AAAdrien Ameye
Adrien Ameye
ABAdrien Badel
Adrien Badel
Extending the frequency bandwidth (BW) of vibration energy harvesters (VEH) that power wireless sensor nodes is of scientific and industrial interest. In this aim, electrical methods to tune the resonant frequency of piezoelectric harvesters with strong electromechanical coupling coefficients have been developed. In this work, we provide guidelines for designing such strongly coupled VEH and present a broadband harvester with high normalized power density (NPD). Through an analytical model, we explain how the coupling coefficient k 2 and the quality factor Q m of a cantilever can be jointly maximized, thereby maximizing the figure of merit k e 2 Q m . The proposed cantilever prototype made of PZN-5.5PT and aluminum offers one of the best coupling coefficients among the state-of-the-art ( k 2 = 49.8%) and a high quality factor ( Q m = 140). Associated to an appropriate tunable electrical interface (short-circuit synchronous electric charge extraction (SECE) in our case), the prototype exhibits a NPD of 12.0 mW g −2 cm −3 and a frequency BW of 36.0% (56.5 Hz around 157 Hz) at 0.34 m s −2 with a tunable electrical interface: the short-circuit SECE. This represents the highest product NPW × BW from state of the art.

2 August 2024 in Energy Conversion and Management
Verified
Journal Article
Closed access
DGDavid Gibus
David Gibus
AMAdrien Morel
Adrien Morel
PGPierre Gasnier
Pierre Gasnier
LCLudovic Charleux
Ludovic Charleux
FFFabien Formosa
Fabien Formosa
ABAdrien Badel
Adrien Badel

28 July 2020 in IEEE Solid-State Circuits Letters
Verified
Journal Article
Closed access
AMAdrien Morel
Adrien Morel
AQA. Quelen
A. Quelen
CBCarlos Augusto Berlitz
Carlos Augusto Berlitz
DGDavid Gibus
David Gibus
PGP. Gasnier
P. Gasnier
GPG. Pillonnet
G. Pillonnet
The harvesting frequency bandwidth (HBW) of a resonant-based electromechanical harvester is inherently limited by its quality factor. Electrical tuning of the resonant frequency leveraged by a significant electromechanical coupling is a promising approach to enhance the HBW and paves the way toward industrialization of robust vibration energy harvesting system. However, it remains challenging to design a self-powered harvesting IC that includes self-tuning capabilities, especially at low vibration amplitude. This paper describes the shorted synchronous electrical charge extraction (SSECE) strategy and proposes a dedicated self-powered integrated circuit including power stage, sensors to sequence the harvesting phases and power sensing. An on-chip tracker dynamically maximizes the harvesting power when the piezoelectricbased harvester characteristics or excitation frequency shifts. The experimental results show a 368% HBW enlargement with the highest convergence FoM (0.213) and the lowest power-peak frequency compared to prior art.

29 July 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
NDNicolas Decroix
Nicolas Decroix
PGPierre Gasnier
Pierre Gasnier
AMAdrien Morel
Adrien Morel
DGDavid Gibus
David Gibus
ABAdrien Badel
Adrien Badel
This article presents the combination of a fast and robust maximum power point tracking algorithm called two-load characterization method (TLCM) and an efficient energy harvesting interface called resistive short circuit (RSC) for broadband piezoelectric energy harvesting. The proposed architecture is implemented using a low-power microcontroller (STM32L4) with its associated discrete electronics. The TLCM consists of an embedded impedance measurement that computes the piezoelectric impedance after two successive phase and voltage measurements. It calculates the optimal load impedance as the complex conjugate of the generator output impedance. It is up to 13 times faster than classical Perturbation and Observation algorithms. The complex conjugate impedance is then emulated by the RSC interface: a Flyback converter emulates a resistive load while a variable duration short-circuit following the zero voltage instant emulates a capacitive load. This two-parameters electrical interface allows a 9.4% harvested power bandwidth, which is 35% more than for a fixed resistor. The whole system is tested at 0.5 m/s 2 peak ambient acceleration and between 26 Hz to 30 Hz in standalone operation. In those conditions, the proposed system showed an end-to-end efficiency in the 65% to 80% range while consuming 21.5 μW to 28.5 μW, with a measurement duty cycle of 13%. It harvests a net maximum power of 157 μW with a peak extracted power of 235 μW.

28 March 2024 in Smart Materials and Structures
Verified
Journal Article
Closed access
ABAya Benhemou
Aya Benhemou
DGDavid Gibus
David Gibus
THThomas Huguet
Thomas Huguet
AMAdrien Morel
Adrien Morel
QDQuentin Demouron
Quentin Demouron
ABAdrien Badel
Adrien Badel
In this article, we propose the modelling of a tunable bistable piezoelectric energy harvester (or BPEH) architecture. The latter is a type of ambient energy converter that continues to gain attention due to their wideband frequency response. As the non-linear dynamics of BPEHs imply significant modeling complexity, dynamic lumped models are necessary to predict BPEHs’ dynamic response and should fit the type of architecture studied. The BPEH architecture of interest uses post-buckled beams to create bistability and an amplified piezoelectric actuator (or APA) to convert the ambient vibrations. To date, no dynamic lumped models have been found in existing literature that account for both the electromechanical conversion and the dynamic behavior of buckled beams, with a specific focus on their axial and bending stiffness, for this BPEH architecture. Additionally, the proposed BPEH architecture offers buckling level tunability, which is achieved using an additional APA. Hence, the aim of this paper is to propose a new lumped model for a BPEH architecture that considers the effect of the post-buckled beams’ stiffness and of the additional APA through an elasticity factor κ ― . This lumped model is established using Euler Lagrange equations and is experimentally validated on a tunable BPEH prototype. This validation shows an average relative error below 6% between the model predictions and experimental dynamic response of the prototype to an ascending frequency sweep, compared to an average relative error that is around 14% for the model proposed in literature. Moreover, numerical simulations using the proposed model lead to the conclusion that there is an optimal elasticity factor κ ― that ensures the maximum power output while maintaining the frequency bandwidth.