Mari Carmen Taboada

Dr. Mari Carmen Taboada

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
MVMireia Vilanova
Mireia Vilanova
MTMari Carmen Taboada
Mari Carmen Taboada
AAAna Martinez Amesti
Ana Martinez Amesti
ANAndrea Niklas
Andrea Niklas
MSMaria San Sebastian
Maria San Sebastian
Teresa GurayaTeresa Guraya
Teresa Guraya
Inconel 738LC (IN738LC) is a nickel-based superalloy specially used in the hot section components of turbine engines. One of its main drawbacks relies on the cracking susceptibility when it is manufactured by laser powder bed fusion (LPBF). This paper analyzes the influence of minor alloying element concentration on cracking tendency of IN738LC superalloy manufactured by LPBF. For that objective, samples were manufactured using two powders, which presented different minor alloying elements concentration (Si, Zr and B). It was shown that the samples crack tendency was very different depending on the powder used for their manufacturing. In fact, the measured crack density value was 2.73 mm/mm2 for the samples manufactured with the powder with higher minor alloying elements concentration, while 0.25 mm/mm2 for the others. Additionally, a special emphasis has been put on elemental composition characterization in cracked grain boundaries in order to quantify possible Si or Zr enrichment. It has been also studied the differences of solidification ranges and grain structures between both samples as a consequence of different minor alloying elements concentration in order to analyze their effect on crack susceptibility. In this sense, Scheil-Gulliver simulation results have shown that samples with higher Si and Zr contents presented higher solidification range temperature. This fact, as well as an increase of the presence of high angle grain boundaries (HAGB), leaded to an increment in the crack formation during solidification. Therefore, in this research work, an understanding of the factors affecting crack phenomenon in the LPBF manufactured IN738LC was accomplished.

2 October 2021 in Crystals
Verified
Journal Article
Open access
PDF file
Juan Carlos Pereira FalconJuan Carlos Pereira Falcon
Juan Carlos Pereira Falcon
JAJon Aranzabe
Jon Aranzabe
MTMari Carmen Taboada
Mari Carmen Taboada
NRNoelia Ruiz
Noelia Ruiz
Pedro Pablo RodríguezPedro Pablo Rodríguez
Pedro Pablo Rodríguez
In this work, new customized heat treatments for selective laser melted (SLM) parts in IN718 alloy were analyzed. This was done through the evaluation of the mechanical properties and advanced characterization of the phases and microstructure obtained in as-built condition and after the application of standard and tailored heat treatments. The microstructure and mechanical properties were compared and discussed with results reported in the literature. Finally, strengthening mechanisms of IN718 alloy processed by SLM and its differences with mechanisms that occur in investment casting were analyzed. Both processes generate quite different microstructures, investment casting is composed mainly by a dendritic structure, and SLM is characterized by columnar and cellular structures with very thin cells. Due to the fine and homogeneous microstructure obtained from SLM processing and its specific strengthening mechanisms, it is not necessary to apply homogenization and solution stages as in standard heat treatment used for this type of alloy in casting or wrought. The pre-heating and process parameters selected, in combination with a direct stepped aging (at 720 °C/620 °C), provide the material with its best mechanical properties, which are superior to those obtained by standard heat treatment (AMS 5383F) applied to investment casting of IN718 alloy.

15 May 2025 in Metals
Verified
Journal Article
Open access
PDF file
MTMari Carmen Taboada
Mari Carmen Taboada
MCMariane Chludzinski
Mariane Chludzinski
RGRaúl Gómez González
Raúl Gómez González
EAEgoitz Aldanondo
Egoitz Aldanondo
The demand for electric mobility has driven the development of advanced laser welding technologies such as dual beam welding and beam shaping. Nevertheless, some intrinsic characteristics present challenges to exploring all its benefits. In this sense, this study investigates the effect of the laser welding parameters employed on the weld quality in busbar–battery interconnects. Dual beam and beam shaping strategies were applied in Al-Al (AA1050 H24) and Al-Cu (AA1050 H24 and C11000) overlap joint configurations adopting statistical methods. For Al-Al joints, welding speed was the most significant parameter influencing interface width, whereas in Al-Cu joints, core power was the only significant parameter affecting both interface width and penetration in the studied configuration. Common defects, such as porosity and cracks, were observed in both material combinations. In Al-Al joints, higher welding speeds resulted in up to a 16% (65.6 HV) increase in hardness, while, in Al-Cu joints, the peak value reached around 900 HV in the interface zone due to the formation of intermetallic compounds (IMCs). In addition, IMCs with complex structures and significant compositional variations, including Cu9Al4 and CuAl2 were identified.

15 November 2016 in Materials Science Forum
Verified
Journal Article
Closed access
PDF file
MTMari Carmen Taboada
Mari Carmen Taboada
IGI. Gutiérrez
I. Gutiérrez
DJDenis Jorge
Denis Jorge
SBS.M.C. van Bohemen
S.M.C. van Bohemen
FHF. Hisker
F. Hisker
GPGeorg Paul
Georg Paul
New trends focused on achieving higher performance steels has led to a so-called 3rd Generation Advanced High Strength Steels (AHSS), in which the typical polygonal ferrite found in TRIP steels as a matrix phase is replaced by harder phases as Carbide-Free Bainite (CFB) and/or (tempered) martensite. Besides, large volume fractions of retained austenite (R.A.) with adequate stability are aimed for to improve the formability of the steels. Si containing steels are regarded as the most suitable to retard cementite formation and consequently reach high volume fractions of RA. In this work, CFB annealing schedules were applied to dilatometer samples of Fe-0.22C-2.0Mn-1.3Si. The overaging temperature TB was varied between 390 oC and 480 oC, and other processing variables investigated were the austenitizing temperature Taus, and the overaging holding time tB. The annealed samples analyzed with LOM, FEG-SEM, EBSD and X-ray diffraction techniques show that markedly different complex microstructures made up of bainite, ferrite, MA phase and retained austenite (R.A) are accomplished depending on the specific thermal cycle. These results are described in detail and discussed in relation to the dilatometry measurements.