Head of Chair for Mechanics with Focus on Structural Health Monitoring, Department of Mechanical Engineering, University of Siegen, 57076 Siegen, Germany
Prof. Dr. Peter Kraemer
Head of Chair for Mechanics with Focus on Structural Health Monitoring, Department of Mechanical Engineering, University of Siegen, 57076 Siegen, Germany
This paper presents a novel approach to address noise, vibration, and harshness (NVH) issues in electrically assisted bicycles (e-bikes) caused by the drive unit. By investigating and optimising the structural dynamics during early product development, NVH can decisively be improved and valuable resources can be saved, emphasising its significance for enhancing riding performance. The paper offers a comprehensive analysis of the e-bike drive unit’s mechanical interactions among relevant components, culminating—to the best of our knowledge—in the development of the first high-fidelity model of an entire e-bike drive unit. The proposed model uses the principles of elastic multi body dynamics (eMBD) to elucidate the structural dynamics in dynamic-transient calculations. Comparing power spectra between measured and simulated motion variables validates the chosen model assumptions. The measurements of physical samples utilise accelerometers, contactless laser Doppler vibrometry (LDV) and various test arrangements, which are replicated in simulations and provide accessibility to measure vibrations onto rotating shafts and stationary structures. In summary, this integrated system-level approach can serve as a viable starting point for comprehending and managing the NVH behaviour of e-bikes.
This paper reports a convolutional neural network (CNN)-based damage detection approach for radar-based structural health monitoring of wind turbine blades. Subsequent radar measurements are transformed into an image-type representation for use as CNN input. In contrast to conventional approaches that require compensation for temperature and loading effects, the proposed framework inherently learns all required information during the training phase. Its damage detection performance (i.e., detecting intact vs. damaged condition) is demonstrated using measurements from multiple embedded radar sensors during fatigue testing of a wind turbine blade with a length of 31 m. The achieved F1-score for correct damage classification is between 91% and 100% for both the unloaded and the loaded blade.
1 October 2019 in International Journal of Rail Transportation
This article deals with the damage detection at the suspension of a railway freight waggon and reveals that the measured accelerations change with the damage in a characteristic way. The authors show that the damage of the suspension is accompanied by a reduction in spring energy which causes a shift of the higher vibration modes in the measured signals. In this context, the paper did not intend to present new methodologies for damage identification. However, the simple findings from the experimental tests can be useful for the design of Structural Health Monitoring (SHM) systems for railway vehicles. At the end, a simple SHM approach for a low number of sensors with practice-oriented positions at the waggon is proposed.
The design-related behaviour of structural dynamics for electric-assisted bicycle (e-bike) drive units significantly influences the mechanical system—e.g., vibrations and durability, stresses and loads, or functionality and comfort. Identifying the underlying mechanical principles opens up optimisation possibilities, such as improved e-bike design and user experience. Despite its potential to enhance the system, the structural dynamics of the drive unit have received little research attention to date. To improve the current situation, this paper uses a flexible multibody modelling approach, enabling new insights through virtual trials and analyses that are not feasible solely from measurements. The incorporation of the drive unit’s system-level topology regarding mass, moment of inertia, stiffness, and damping enables the analysis of critical system states. Experiments accompany the analysis and validate the model by demonstrating a load-dependent shift of the first torsional mode around 35 Hz to 60 Hz, capturing comparable resonance frequency ranges up to 6 kHz, and yielding qualitatively consistent peak positions in both steady-state and ramp-up analyses (mean deviations of 0.03% and 0.06%, respectively). Theoretical considerations of the multibody system highlight the effects, and the stated modelling restrictions make the method’s limitations transparent. The key findings are that the drive unit’s structural dynamic behaviour exhibits solely one structural mode until 0.5 kHz, and further 27 modes up to 10 kHz, solely originating due to the multibody arrangement of the drivetrain. These modes are also load-dependent and lead to resonances during operation. In summary, the approach enables engineers, for the first time, to significantly improve the structural dynamics of the e-bike drive unit using a full-scale system model.
This work presents an experimental investigation of a stand alone directional structural health monitoring (SHM) system based on a frequency-steerable acoustic transducer (FSAT) operating in pulse–echo mode. A single transducer bonded at the center of a 1000 × 1000 × 1 mm aluminum plate was used to perform damage detection and localization by exploiting the frequency-dependent beam steering characteristics of the FSAT. Directional scanning of the surrounding structure was achieved without mechanical movement or phased-array electronics. Damage detection employed baseline comparison using a root mean square metric applied to reflected Lamb wave signals. Both directional detection at fixed actuation frequencies and spatial scanning via frequency sweeps were experimentally demonstrated. The system successfully detected and localized multiple damage types, including drilled holes and attached disk masses with a diameter of mm, with characteristic dimensions as small as 3 mm. Progressive detection and discrimination of single, double, and triple damage scenarios at distinct angular locations validated the FSAT’s capability for complex multidamage monitoring. The localization accuracy was consistent with the transducer’s angle–frequency calibration, and time-of-flight measurements provided the radial distance estimation capabilities. Compared to conventional omnidirectional sensor networks or phased-array systems, the presented solution offers reduced system complexity, lower sensor density, and improved scalability, while remaining compatible with existing ultrasonic sensor networks. These results demonstrate the potential of the FSAT for simpler, lighter, and more scalable autonomous SHM systems, with enhanced inspection flexibility and localization accuracy suitable for industrial applications.
Radar technology in the microwave and millimeter-wave frequency range is the subject of current research for structural health monitoring of composite materials, e.g., damage detection in wind turbine blades. Performance assessment, enabling widespread practical application of this promising and non-contact sensing approach, can be realized via probability of detection (POD) theory, which is a statistical method for determining the detectability of damage through response metrics as a function of flaw size. This paper deals with the experimental investigation of a delamination model represented by two parallel glass fiber reinforced polymer plates separated from each other from to in steps of . Experimental studies with a frequency modulated continuous wave radar are performed under laboratory conditions in the frequency range from to . The signal response is represented by two damage indicators (DIs), according to the root mean square deviation and Mahalanobis distance. Since the reflection of electromagnetic waves exhibits a nonlinear behavior, this also implies a nonlinear response in the DI characteristic. The novelties in this work are the successful implementation of a nonlinear regression model, combined with an optimal threshold decision through receiver operating characteristic curves for a high-resolution POD representation. The POD with confidence bounds indicates the flaw size at which the delamination can be detected reliably. Depending on the radar distance in experimental studies, the binary structural condition (damaged or undamaged) was correctly assessed from to . The minimum detectable size ranges from to .