Usage of waste materials as concrete mixture can reduce the waste management crisis in the world. Used tyres were widely researched as an alternative source of aggregates replacement in concrete mixture. This research is to study the behaviour of concrete incorporating rubber tyre crumb as fine aggregate replacement. The workability, compression strength and water absorption of this concrete will be determined and then compared to normal concrete. Motorcycle inner tube will be used as rubber source and it will be shredded to crumbs. Three samples of concrete with rubber as fine aggregates were prepared. Rubber crumbs will be used to replace fine aggregates in 2.5, 5.0 and 7.5% in mass. Normal concrete were prepared separately as control for comparison. Concrete mixture of 1:2:4 and 0.5 of water cement ratio were used. Slump test were done to test the workability of each mix. Twelve sample cubes from (150mm x 150mm x 150mm) each mix were prepared and cured for 7, 14 and 28 days. Compression tests were performed for each mix cube at age 7, 14 and 28 days. Water absorption test were done at age 28 days. Results revealed that rubberized concrete has better workability than normal concrete. They also have smaller compressive value and higher water absorption compared to normal concrete.
Cold-bonded pelletizing technique is frequently used in aggregate manufacturing process as it can minimise the energy consumption. It has contributed to both economical and environmental advantages because it helps to reduce the gas emissions problems. Bottom ash collected from municipal solid waste incineration (MSWI) plant was selected as raw material in this study and was utilised as a partial replacement for cement for artificial aggregate production. Several percentage of ash replacement was selected ranged from 10 to 50%. Aggregate pellets were subjected to different types of curing condition which is room-water (RW), room-room (RR), oven-room (OR) and oven-water (OW) condition. Properties of aggregate pellets were examined to obtain its density, water absorption, aggregate impact value (AIV) and specific gravity (SG). The results indicated that the most efficient curing regime is by exposing the aggregate in RW condition. The optimum aggregate was selected at 20% where it has satisfied the required density of 739.5kg/m3, and classified as strong aggregate with AIV 14. However, the water absorption of aggregate increased proportionately with the increment of ash content.
1 May 2021 in Journal of Physics: Conference Series
Food processing of fucuk making from soy milk from conventional method is evaluated as the case study. The cost, time, fuel supply security and environmental issue anticipated within the process had called for a new approach innovation. Electromagnetic induction heating has been distinguished between other technologies for the purpose. The design, test, analysis and field test of the proposed system has been presented in this report. The installed system seems to outfit and satisfy the industry requirements and can be expanded to other food processing field as well. The advantage and limitation are also discussed within the report.
1 December 2020 in IOP Conference Series: Earth and Environmental Science
This study focusses on the development of new lightweight aggregate (LWA) that eventually will have comparable properties with existing natural aggregate which is granite. The main objectives of this study is to examine potential use of recycled municipal solid waste incineration (MSWI) ash as raw material in LWA production with a method of cold-bonded palletization process. The ashes are collected from Cameron Highland Incineration Plant, Malaysia that can be divided into bottom ash (BA) and fly ash (FA). This study uses FA as partial raw material to substitute the Ordinary Portland Cement (OPC). The properties FA are studied by means of X-Ray Fluorescence (XRF). The LWA is fly ash lightweight aggregate (FALA). The production of LWA is based on cold-bonded palletization technique. FALA have experienced two different curing process for 28 days namely room-room (RR) and room-water (RW) curing conditions. The percentage of FA used in this study is 10%, 20%, 30%, 40% and 50% of cement replacement and the size is fixed between 10 mm to 20 mm with circular shape. The properties of FALA produced in this study is examined including loose bulk density, and aggregate impact value (AIV). Other physical properties including colour and texture are also being investigated. From the results of LWA it is clearly seen that 20% FA were the best percentage of ash used to produce good quality LWA. Loose bulk density of FALA selected is 716.72 kg/m3 and AIV 13.80%.
28 February 2022 in Archives of Metallurgy and Materials
This study focused on the reclamation of ash from incineration process and development of new artificial lightweight aggregate (LWA) that have comparable properties with existing natural coarse aggregate. The main objective of this study is to examine potential use of recycled municipal solid waste incineration (MSWI) ash as raw material in LWA production with a method of cold-bonded pelletization. Two types of incineration ash which is bottom ash (BA) and fly ash (FA) were collected from Cameron Highland Incineration Plant, Malaysia. The properties of BA and FA are studied by means of X-Ray Fluorescence (XRF) and microstructure of these ashes were inspected using Scanning Electron Microscope (SEM). The properties of BALA and FALA produced in this study is examined including loose bulk density, water absorption and aggregate impact value (AIV). From the results of both types of artificial LWA, the lowest loose bulk density of BALA is BALA50 with 564.14 kg/m3 and highest is at 831.19 kg/m3. For FALA50, lowest loose bulk density is 573.64 kg/m3 and highest is 703.35 kg/m3. Water absorption of BALA and FALA is quite similar with one another in with the value of 23.8% and 22.6%, respectively. Generally, FALA have better qualities of LWA comparing with BALA with lower bulk density and water absorption and can be categorized as strong aggregate. In summary, reclamation and reutilization of incinerator ash has generated acceptable qualities for artificial LWA. Both types of BA and FA shown a great potential to be recycled as additional materials in artificial aggregate production.
15 June 2023 in International Journal of Conservation Science