Reverse osmosis (RO) desalination is considered a viable alternative to reduce water scarcity; however, its energy consumption is high. Photovoltaic (PV) energy in desalination processes has gained popularity in recent years. The temperature is identified as a variable that directly affects the behavior of different parameters of the RO process and energy production in PV panels. The objective of this study was to evaluate the effect of temperature on energy consumption and polarization factor in desalination processes at 20, 23, 26 and 30 °C. Tests were conducted on a RO desalination plant driven by a fixed 24-module PV system that received spray cooling in the winter, spring and summer seasons. The specific energy consumption was lower with increasing process feed temperature, being 4.4, 4.3, 3.9 and 3.5 kWh m⁻³ for temperatures of 20, 23, 26 and 30 °C, respectively. The water temperature affected the polarization factor, being lower as the temperature increased. The values obtained were within the limits established as optimal to prevent the formation of scaling on the membrane surface. The spray cooling system was able to decrease the temperature of the solar cells by about 6.2, 13.3 and 11.5 °C for the winter, spring and summer seasons, respectively. The increase in energy production efficiency was 7.96–14.25%, demonstrating that solar cell temperature control is a viable alternative to improve power generation in solar panel systems.

This study investigates the corrosion resistance of chitosan and its crosslinked form coatings applied on stainless steel as substrate using various analytical techniques. Fourier transform infrared spectroscopy (FTIR-ATR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were employed for surface characterization. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization (PDP) techniques were used to analyze the electrochemical behavior. Four coatings were evaluated along with naked stainless steel (ss): chitosan (Chi), chitosan crosslinked with ammonium paratungstate (Chi/PTA), chitosan crosslinked with polyethylene glycol (Chi/PEG), and chitosan crosslinked with polyvinylpyrrolidone (Chi/PVP). Electrochemical measurement parameters analysis assessed the coating corrosion resistance, such as impedance modulus (|Z|) and corrosion potential (Ecorr). Results indicate varying degrees of corrosion resistance among the coatings. Chi/PTA exhibited notable characteristics in the electrochemical tests, showing promising polarization resistance (Rp) and impedance behavior trends. Conversely, Chi/PEG showed differing electrochemical responses, suggesting higher susceptibility to corrosion under the study conditions. These findings contribute to understanding the electrochemical performance of chitosan-based coatings on stainless steel, highlighting their potential in corrosion protection applications.

Metals are widely used in various industrial applications due to their advantageous properties, but they often exhibit signs of degradation over time because of prolonged exposure to environmental conditions. To prevent corrosion, coatings have gained popularity owing to their practicality in maintaining the original shape and dimensions of the object being protected. Nevertheless, traditional coatings may pose significant toxicological and environmental concerns, leading researchers to explore eco-friendly alternatives such as chitosan-based coatings. Chitosan, a biopolymer derived from chitin, is abundant in nature and has been extensively studied for its physicochemical properties, including its potential in the development of new materials. Chitosan-based coatings have shown promise as effective corrosion inhibitors, and this study aims to develop a crosslinked chitosan-based coating from shrimp waste as an alternative to expensive, commercial coatings. Chitosan, and chemically modified polyethylene glycol, polyvinylpyrrolidone, and ammonium paratungstate chitosan coatings of high- and medium molecular weight prepared by the sol-gel technique, were used for the study of corrosion protection of aluminum in 3.5% synthetic seawater. The molecular interactions and structural alterations following cross-linking of chitosan-based coatings was supported by FTIR-ATR. Surface morphology analysis by AFM indicated good coating adsorption on aluminum surfaces. Contact angle measurements showed hydrophilic properties with contact angles >62° and <90°. Physicochemical characterization (molecular weight (kDa), deacetylation (%), humidity (%), and ash (%)) was also carried out. The corrosion inhibition effectiveness was assessed by gravimetric tests after immersion studies, and the results highlighted the MMW-Chi-based coating’s performance.

Reverse osmosis (RO) desalination is a technology that is commonly used to mitigate water scarcity problems; one of its disadvantages is the bio-fouling of the membranes used, which reduces its performance. In order to minimize this problem, this study prepared modified thin film composite (TFC) membranes by the incorporation of chitosan–silver particles (CS–Ag) of different molecular weights, and evaluated them in terms of their anti-biofouling and desalination performances. The CS–Ag were obtained using ionotropic gelation, and were characterized by Fourier transform infrared spectroscopy (FTIR), high-resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA) and dynamic light scattering (DLS). The modified membranes were synthetized by the incorporation of the CS–Ag using the interfacial polymerization method. The membranes (MCS–Ag) were characterized by Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM) and contact angle. Bactericidal tests by total cell count were performed using Bacillus halotolerans MCC1, and anti-adhesion properties were confirmed through biofilm cake layer thickness and total organic carbon (%). The desalination performance was defined by permeate flux, hydraulic resistance, salt rejection and salt permeance by using 2000 and 5000 mg L⁻¹ of NaCl. The MCS–Ag-L presented superior permeate flux and salt rejection (63.3% and 1% higher, respectively), as well as higher bactericidal properties (76% less in total cell count) and anti-adhesion capacity (biofilm thickness layer 60% and total organic carbon 75% less, compared with the unmodified membrane). The highest hydraulic resistance value was for MCS–Ag-M. In conclusion, the molecular weight of CS–Ag significantly influences the desalination and the antimicrobial performances of the membranes; as the molecular weight decreases, the membranes’ performances increase. This study shows a possible alternative for increasing membrane useful life in the desalination process.

A membrane system was applied for ultrapure water production from the treatment of saline effluent from the canned food industry. The industrial effluent presented a high saline concentration, including sodium chloride, calcium carbonate, calcium sulfates, and magnesium. The effluent was treated using a system of reverse osmosis (RO) and a post-treatment process consisting of ion exchange resins (IEXRs). The RO was accompanied by the addition of a hexametaphosphate dose (2, 6, and 10 mg/L) as an antiscalant to avoid the RO membrane scaling by minerals. In turn, IEXRs were used for water deionization to produce ultrapure water with a reduced concentration of monovalent ions. The antiscalant dose was 6 mg/L, producing clean water from RO permeates with an efficiency of 65–70%. The brine from RO was projected for its reuse in food industry processes. The clean water quality from RO showed 20% total dissolved solids (TDS) removal (equivalent to salts). The antiscalant inhibited the formation of calcium salt incrustation > 200 mg/L, showing low fouling. In turn, anionic resins removed 99.8% of chloride ions, whereas the monovalent salts were removed by a mix of cationic–anionic resin, producing ultrapure water with electrical conductivity < 3.3 µS/cm. The cost of ultrapure water production was 2.62 USD/m³.