Koki Ogura

Prof. Koki Ogura


Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 October 2018 in Journal of Modern Power Systems and Clean Energy
Verified
Journal Article
Open access
PDF file
KOKoki Ogura
Koki Ogura
Mohan Lal KOLHEMohan Lal KOLHE
Mohan Lal KOLHE
MNMutsuo Nakaoka
Mutsuo Nakaoka
A unique high efficiency photovoltaic (PV) system is presented. It uses partial sine wave tracking for a pulse-width modulation (PWM) boost converter as well as a full-bridge inverter. The boost converter and full-bridge inverter are connected via a compact intermediate film capacitor (i.e. non-smoothing DC link stage). PWM switching is activated by a dual mode control technique. In the proposed topology, simultaneous switching of both power conversion stages is avoided and therefore this increases the power conversion efficiency. The distinctive operating principles of these two power processing stages are discussed and analyzed with the experimental results for single-phase loading of the PV system.

12 May 2025 in Sensors
Verified
Journal Article
Open access
PDF file
Thunyawat LimpitiThunyawat Limpiti
Thunyawat Limpiti
Charernkiat PochaiyaCharernkiat Pochaiya
Charernkiat Pochaiya
SSSiraporn Sakphrom
Siraporn Sakphrom
SCSaravud Chandhaket
Saravud Chandhaket
PLPrapan Leekul
Prapan Leekul
TTTanawut Tantisopharak
Tanawut Tantisopharak
This study aims to present a low-cost, non-destructive microwave sensor implementation to monitor the real-time moisture content of rubber wood in industrial dehydration processes. The proposed sensor is based on the free-space measurement technique with magnitudes S11 and S21 only. The novelties of this study consist of the natural frequency determination of rubber wood and the design of a sensor system using devices available on the market with reasonable cost performance. The natural frequency was determined using a simulation and was equal to 1.25 GHz. It specified the sensor system design and device selection. The designed system was initially verified by measuring the moisture content of rubber wood in the laboratory. The measured S11 and S21 voltages correlating with moisture content percentages were obtained and programmed. The system was then installed to monitor the moisture content of rubber wood in the dehydration process. The measured results deviated from those obtained from a standard method in the range of 7.67–15.38%. The error compensation was analyzed to improve the measured results that provided the deviated moisture content in the range of 3.58–5.21%. It can be inferred that the proposed sensor system has the capability to be implemented in industrial dehydration processes.

21 January 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
KOKoki Ogura
Koki Ogura
SCSaravud Chandhaket
Saravud Chandhaket
Mohan Lal KOLHEMohan Lal KOLHE
Mohan Lal KOLHE
SSSiraporn Sakphrom
Siraporn Sakphrom
Saad MekhilefSaad Mekhilef
Saad Mekhilef
This paper presents a high-frequency pulse-density-modulated (PDM) soft-switching series load resonant inverter for use in induction heating (IH) fixed roller applications, which is used in copy and printing machines. The proposed simple high-frequency resonant inverter uses an asymmetrical pulse pattern PDM control scheme to achieve complete zero-current soft-switching commutations over a wide output range of input power regulation. Additionally, when the printer toner requires operation in very light load conditions, this causes difficulty in achieving zero-voltage or zero-current soft-switching operations in the IH high-frequency resonant inverters with pulse frequency modulation or pulse width modulation control schemes. The proposed resonant inverter demonstrates the capability to accomplish highly efficient power conversions. In this work, a fixed roller for printing machines is developed for doing experiments to verify the efficiency of the proposed circuit topology and its PDM control schemes. The inverter’s steady-state and transient operating principles are analyzed based on the proposed control strategy at a high-frequency PDM. Operating conditions such as power loss analysis, power conversion efficiency and temperature rise characteristics of the proposed inverter are presented and analyzed through experimental results. Finally, from a practical viewpoint, a comparative study of a conventional halogen lamp heater and the proposed IH fixed roller is deliberated.

29 May 2003 in Electrical Engineering in Japan
Verified
Journal Article
Open access
PDF file
HTHaruo Terai
Haruo Terai
IHIzuo Hirota
Izuo Hirota
TMTakahiro Miyauchi
Takahiro Miyauchi
HOHideki Omori
Hideki Omori
KOKoki Ogura
Koki Ogura
MNMutsuo Nakaoka
Mutsuo Nakaoka
A cost-effective high-efficiency, simple, low-noise voltage-source-type single-ended quasi-resonant high-frequency inverter using a single power semiconductor switching device and its modified circuit topologies are commonly applied to consumer induction-heated rice cookers with a warmer function, cooking heaters, and microwave ovens. This paper presents some comparative performance evaluations of several generations of IGBTs and MCT (MOS Controlled Thyristor) incorporated into the typical voltage-source quasi-resonant inverter operating in zero-voltage soft switching transition mode. The latest generation of IGBT upgraded by lowering the saturation voltage characteristics was designed for consumer power applications in order to reduce conduction losses. The comparative steady-state characteristics of some simple power semiconductor switching devices of several generations of IGBTs are examined on the basis of the simplest single-ended quasi-resonant inverter circuit operating under the zero-voltage soft switching commutating principle. In addition, the power losses and temperature performance analysis of the latest IGBT are discussed and evaluated relative to previously developed IGBTs. Finally, the further reduced saturation voltage and conduction loss characteristics of MCT which are more suitable for consumer utilizations are presented in comparison with the conventional IGBT. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 144(3): 58–68, 2003; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/eej.10151

1 January 2003 in Journal of the Japan Institute of Power Electronics
Verified
Journal Article
Closed access
KOKoki Ogura
Koki Ogura
TNTomomasa Nishida
Tomomasa Nishida
SNShinichiro Nagai
Shinichiro Nagai
MNMutsuo Nakaoka
Mutsuo Nakaoka