An effect of factors determining water quality in the water supply network in Kraków is assessed. Data collected over a four-year research period included quality parameters of water taken from the water distribution system in the period between 1 January 2011 and 31 December 2014. In analysis...

Wood pellets play an important role among biomass materials used as fuel. At the same time, today’s economic, environmental, political and social realities, as well as other circumstances related to fuels used for heat generation, mean that there is demand for increasingly efficient and environmentally friendly combustion sources. As is well known, each combustion source has a different efficiency due to its intended use, design, principle of operation and the type and composition of the fuel burned. The amount of pollutants emitted into the environment during combustion also largely depends on these factors. The aim of this study was to compare the flue gas emissions and efficiency of two pellet burners of different design, burning certified A1 wood pellets from different suppliers. The emission requirements were met during the combustion of wood pellets in a boiler with the two burners tested (one with a moving grate and an overfed burner). The analyses and studies carried out aim to improve the capability of managing the efficiency and environmental performance of the heat source (i.e., a boiler or a burner) and the fuel (type of wood pellets). This is done in the context of demonstrating a better combustion source when selecting the right burner and fuel in terms of efficiency and emissions. In this paper, comparisons of flue gas emissions are presented along with characteristics in the form of graphs, as well as thermal and combustion efficiencies for the corresponding solid fuel used in the form of wood pellets. After comparing the emissions, it was found that the statistical averages of CO, NOx, dust and VOCs were similar for combustion at full power using the burners tested. Taking into account the pollution levels at combustion, it can be said that the difference in CO emissions at full and minimum combustion is lower for the experimental burner compared with the moving grate burner (reference burner). In summary, it can be concluded that the experimental overfed burner under consideration can be successfully used as a solid fuel boiler to burn wood pellets.

This paper presents the results of an examination of an automatic biomass boiler identifying its strengths and weaknesses and computing its seasonal energy and emission parameters. The boiler was found to meet the energy and emission requirements for distribution in Poland. The boiler is characterised by good heating efficiency and low dust and carbon monoxide emissions. The aim of this paper is to provide and analyse these parameters, and by doing so classify it in the context of its competitors. The average heating output is 26.86 kW and the thermal efficiency is 87.97%. Carbon monoxide emissions are very low (22.71 mg/m³). However, nitrogen oxide emissions (187.6 mg/m³) can be a problem. Filters made out of metalworking waste, i.e., machining shavings, significantly improve the boiler performance, contributing to an increased heat output and efficiency and reduced dust emissions. Compared with other solutions available in the market, the boiler compares favourably in terms of dust and carbon monoxide emissions and is also characterised by similar efficiency, especially with the filters in place. Regarding the context of thermal energy management, the appliance under investigation demonstrates not only favourable energy and emission parameters, but also the potential for the efficient use of thermal energy, which can bring additional economic and environmental benefits.

In the paper, the authors focused on the environmental problems of pollution emissions caused by households using batch boilers fired with solid fuels. The aim of this study is to analyse the course of changes in the actual efficiency and emission of a solid fuel updraft boiler, the most popular type of batch boilers used in Poland in recent years. The subject of analysis is the comparison of the values of atmospheric emissions of harmful substances depending on the type of wood burnt in the boiler. The investigation comprises the combustion characteristics of three types of woody biomass (in billets), i.e., pine, birch, and beech. Based on the carried out research of all billets, the beech has the lowest values of CO (3497 mg/m³) and particulate matter (116.9 mg/m³). Despite this, obtained results exceed the current permissible limits based on the standard PN:EN 303-5:2012. The highest efficiency (54.13%) was obtained for birch billets, the lowest for pine (45.13%). The research has shown that the real heating efficiency during the combustion of wood, irrespective of the type of wood being burnt, is low. To summarise, the outdated installations contribute to air pollution several times higher, which indicates the need to replace inefficient heat sources using solid fuels with modern equipment that meets the most stringent standards.

The purpose of the study is to investigate the energy performance of a PVT collector in combination with a heat pump. First, a test system combining a heat pump and PVT module is built, and then its performance is carefully measured, assessing the electricity and heat production. The paper focuses on increasing the efficiency of a photovoltaic (PV) panel (as part of the PVT module) by cooling it with a heat pump. The main idea is to use the heat generated by the warming panels as a low-temperature source for the heat pump. The research aims to maximize the use of solar energy in the form of both electricity and heat. In traditional PV systems, the panel temperature rise reduces the solar-to-electric conversion efficiency. Therefore, cooling with a heat pump is increasingly used to keep panels at optimal temperatures and improve performance. The tests confirm that cooling the panels with a heat pump results in an 11.4% improvement in electrical efficiency, an increase from 10.8% to 12.0%, with an average system efficiency of 11.81% and a temperature coefficient of –0.37%/°C. The heat pump achieves a COP of 3.45, while thermal energy from the PVT panel accounts for up to 60% of the heat input when the air exchanger is off. The surface temperature of the PVT panels varies from 11 °C to 70 °C, and cooling enables an increase in electricity yield of up to 20% during sunny periods. This solution is especially promising for facilities with year-round thermal demand (e.g., swimming pools, laundromats).

The reduction of harmful emissions is shaping trends across many industries, including architecture and building. With rising ecological awareness and the threat of climate change, architects, construction engineers, and developers are focusing on innovative solutions to minimize the construction sector’s environmental impact. This paper presents a technical and management approach system using renewable energy sources, based on an existing single-family house with known energy consumption. The aim is to achieve energy independence by relying solely on on-site electricity generation and storage, while remaining connected to water and sewage infrastructure. Utilizing renewable energy sources enhances self-sufficiency and investment profitability. The study evaluates the house’s energy consumption to optimally select electricity supply solutions, including a small wind farm and photovoltaic installation integrated with appropriate electricity storage. This is crucial due to the air heat pump used for heating and domestic hot water, which requires electricity. An hourly simulation of the system’s operation over a year verified the adequacy of the selected devices. Additionally, two different locations were analyzed to assess how varying climate and wind conditions influence the design and performance of off-grid energy systems. The analysis showed that solar and wind systems can meet annual energy demand, but limited storage capacity prevents full autonomy. Replacing the heat pump with a biomass boiler reduces electricity use by about 25% and battery needs by 40%, though seasonal energy surpluses remain a challenge. This concept aligns with the goal of achieving climate neutrality by 2050.