With sustainable energy being the key to reaching climate neutrality, the utilization of non-wooden biomass is a necessity. This article compares the emissions and efficiency of combusting a number of types of agrobiomass and wood pellets. A comparison was made on a moving grate pellet burner mounted in a boiler, where flue gas had a vertical flow via two pass heat exchangers with turbulization elements. Tests were conducted on wood pellets (ENPlus), miscanthus straw pellets, sunflower husk pellets, and corn stover pellets. During combustion, both wood and miscanthus pellets met the PN-EN 303-5:2012 emission and efficiency requirements. Corn stover pellets met the requirement on the nominal capacity. Sunflower husk pellets are characterized by excessive CO and particulate matter emissions. Sunflower husk pellets were the most problematic fuel from the point of view of the results of this research. During combustion of the miscanthus straw pellets there was a need to decrease the nominal heating capacity due to ash sintering.

The article presents the results of research on the efficiency of photovoltaic (PV) modules cooled with water. The aim of the experiment was to improve the working conditions of solar modules. A temperature decrease was obtained for the PV module by pouring cool tap water onto the upper surface of the modules, either in imitation of rain or as a water film. The power of the cooled and non-cooled devices were then compared. The temperature of the cooled modules dropped to almost 25 °C, whilst the temperature of the non-cooled module was 45 °C. The best results were achieved by cooling modules with a water film, since there were no water splashes, and the continuous cooling of the surface leads to a 20% increase in power. During the test, the non-cooled module attained a maximum power of 105.3 W/m², compared to 125.5 W/m² for its cooled counterpart. Cooling the module, therefore, resulted in a power increase of 20.2 W/m². The results of the work may be of particular interest for small installations, especially because it cleans the modules while providing an increase in power.

Krakow has an extensive district heating network, which is approximately 900 km long. It is the second largest city in terms of the number of inhabitants in Poland, resulting in a high demand for energy—for both heating and cooling. The district heating of the city is based on coal. The paper presents the conception of using the available renewable sources to integrate them into the city’s heating system, increasing the flexibility of the system and its decentralization. An innovative solution of the use of hybrid, modular heat pumps with power dependent on the needs of customers in a given location and combining them with geothermal waters and photovoltaics is presented. The potential of deep geothermal waters is based on two reservoirs built of carbonate rocks, namely Devonian and Upper Jurassic, which mainly consist of dolomite and limestone. The theoretical potential of water intake equal to the nominal heating capacity of a geothermal installation is estimated at 3.3 and 2.0 MW, respectively. Shallow geothermal energy potential varies within the city, reflecting the complex geological structure of the city. Apart from typical borehole heat exchangers (BHEs), the shallower water levels may represent a significant potential source for both heating and cooling by means of water heat pumps. For the heating network, it has been proposed to use modular heat pumps with hybrid sources, which will allow for the flexible development of the network in places previously unavailable or unprofitable. In the case of balancing production and demand, a photovoltaic installation can be an effective and sufficient source of electricity that will cover the annual electricity demand generated by the heat pump installation, when it is used for both heating and cooling. The alternating demand of facilities for heating and cooling energy, caused by changes in the seasons, suggests potential for using seasonal cold and heat storage.

Wood pellets play an important role among biomass materials used as fuel. At the same time, today’s economic, environmental, political and social realities, as well as other circumstances related to fuels used for heat generation, mean that there is demand for increasingly efficient and environmentally friendly combustion sources. As is well known, each combustion source has a different efficiency due to its intended use, design, principle of operation and the type and composition of the fuel burned. The amount of pollutants emitted into the environment during combustion also largely depends on these factors. The aim of this study was to compare the flue gas emissions and efficiency of two pellet burners of different design, burning certified A1 wood pellets from different suppliers. The emission requirements were met during the combustion of wood pellets in a boiler with the two burners tested (one with a moving grate and an overfed burner). The analyses and studies carried out aim to improve the capability of managing the efficiency and environmental performance of the heat source (i.e., a boiler or a burner) and the fuel (type of wood pellets). This is done in the context of demonstrating a better combustion source when selecting the right burner and fuel in terms of efficiency and emissions. In this paper, comparisons of flue gas emissions are presented along with characteristics in the form of graphs, as well as thermal and combustion efficiencies for the corresponding solid fuel used in the form of wood pellets. After comparing the emissions, it was found that the statistical averages of CO, NOx, dust and VOCs were similar for combustion at full power using the burners tested. Taking into account the pollution levels at combustion, it can be said that the difference in CO emissions at full and minimum combustion is lower for the experimental burner compared with the moving grate burner (reference burner). In summary, it can be concluded that the experimental overfed burner under consideration can be successfully used as a solid fuel boiler to burn wood pellets.

This paper presents the results of an examination of an automatic biomass boiler identifying its strengths and weaknesses and computing its seasonal energy and emission parameters. The boiler was found to meet the energy and emission requirements for distribution in Poland. The boiler is characterised by good heating efficiency and low dust and carbon monoxide emissions. The aim of this paper is to provide and analyse these parameters, and by doing so classify it in the context of its competitors. The average heating output is 26.86 kW and the thermal efficiency is 87.97%. Carbon monoxide emissions are very low (22.71 mg/m³). However, nitrogen oxide emissions (187.6 mg/m³) can be a problem. Filters made out of metalworking waste, i.e., machining shavings, significantly improve the boiler performance, contributing to an increased heat output and efficiency and reduced dust emissions. Compared with other solutions available in the market, the boiler compares favourably in terms of dust and carbon monoxide emissions and is also characterised by similar efficiency, especially with the filters in place. Regarding the context of thermal energy management, the appliance under investigation demonstrates not only favourable energy and emission parameters, but also the potential for the efficient use of thermal energy, which can bring additional economic and environmental benefits.

In the paper, the authors focused on the environmental problems of pollution emissions caused by households using batch boilers fired with solid fuels. The aim of this study is to analyse the course of changes in the actual efficiency and emission of a solid fuel updraft boiler, the most popular type of batch boilers used in Poland in recent years. The subject of analysis is the comparison of the values of atmospheric emissions of harmful substances depending on the type of wood burnt in the boiler. The investigation comprises the combustion characteristics of three types of woody biomass (in billets), i.e., pine, birch, and beech. Based on the carried out research of all billets, the beech has the lowest values of CO (3497 mg/m³) and particulate matter (116.9 mg/m³). Despite this, obtained results exceed the current permissible limits based on the standard PN:EN 303-5:2012. The highest efficiency (54.13%) was obtained for birch billets, the lowest for pine (45.13%). The research has shown that the real heating efficiency during the combustion of wood, irrespective of the type of wood being burnt, is low. To summarise, the outdated installations contribute to air pollution several times higher, which indicates the need to replace inefficient heat sources using solid fuels with modern equipment that meets the most stringent standards.