With sustainable energy being the key to reaching climate neutrality, the utilization of non-wooden biomass is a necessity. This article compares the emissions and efficiency of combusting a number of types of agrobiomass and wood pellets. A comparison was made on a moving grate pellet burner mounted in a boiler, where flue gas had a vertical flow via two pass heat exchangers with turbulization elements. Tests were conducted on wood pellets (ENPlus), miscanthus straw pellets, sunflower husk pellets, and corn stover pellets. During combustion, both wood and miscanthus pellets met the PN-EN 303-5:2012 emission and efficiency requirements. Corn stover pellets met the requirement on the nominal capacity. Sunflower husk pellets are characterized by excessive CO and particulate matter emissions. Sunflower husk pellets were the most problematic fuel from the point of view of the results of this research. During combustion of the miscanthus straw pellets there was a need to decrease the nominal heating capacity due to ash sintering.

Wood pellets play an important role among biomass materials used as fuel. At the same time, today’s economic, environmental, political and social realities, as well as other circumstances related to fuels used for heat generation, mean that there is demand for increasingly efficient and environmentally friendly combustion sources. As is well known, each combustion source has a different efficiency due to its intended use, design, principle of operation and the type and composition of the fuel burned. The amount of pollutants emitted into the environment during combustion also largely depends on these factors. The aim of this study was to compare the flue gas emissions and efficiency of two pellet burners of different design, burning certified A1 wood pellets from different suppliers. The emission requirements were met during the combustion of wood pellets in a boiler with the two burners tested (one with a moving grate and an overfed burner). The analyses and studies carried out aim to improve the capability of managing the efficiency and environmental performance of the heat source (i.e., a boiler or a burner) and the fuel (type of wood pellets). This is done in the context of demonstrating a better combustion source when selecting the right burner and fuel in terms of efficiency and emissions. In this paper, comparisons of flue gas emissions are presented along with characteristics in the form of graphs, as well as thermal and combustion efficiencies for the corresponding solid fuel used in the form of wood pellets. After comparing the emissions, it was found that the statistical averages of CO, NOx, dust and VOCs were similar for combustion at full power using the burners tested. Taking into account the pollution levels at combustion, it can be said that the difference in CO emissions at full and minimum combustion is lower for the experimental burner compared with the moving grate burner (reference burner). In summary, it can be concluded that the experimental overfed burner under consideration can be successfully used as a solid fuel boiler to burn wood pellets.

This paper presents the results of an examination of an automatic biomass boiler identifying its strengths and weaknesses and computing its seasonal energy and emission parameters. The boiler was found to meet the energy and emission requirements for distribution in Poland. The boiler is characterised by good heating efficiency and low dust and carbon monoxide emissions. The aim of this paper is to provide and analyse these parameters, and by doing so classify it in the context of its competitors. The average heating output is 26.86 kW and the thermal efficiency is 87.97%. Carbon monoxide emissions are very low (22.71 mg/m³). However, nitrogen oxide emissions (187.6 mg/m³) can be a problem. Filters made out of metalworking waste, i.e., machining shavings, significantly improve the boiler performance, contributing to an increased heat output and efficiency and reduced dust emissions. Compared with other solutions available in the market, the boiler compares favourably in terms of dust and carbon monoxide emissions and is also characterised by similar efficiency, especially with the filters in place. Regarding the context of thermal energy management, the appliance under investigation demonstrates not only favourable energy and emission parameters, but also the potential for the efficient use of thermal energy, which can bring additional economic and environmental benefits.

The energy obtained from biomass in the global balance of energy carriers is the largest source among all RES. It should be borne in mind that the share of biomass as an energy carrier in the total balance is as much as 14%. The basic sources of renewable energy used in Poland are the wind power...

Wood pellets, commonly referred to as biomass fuel, are increasingly used in heating and district heating in the European Union countries, including Poland. Their use in class 5 and/or Ecodesign boilers enables an individual consumer to use energy from renewable sources, reduce the environmental...