Guang Li

Dr. Guang Li


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
Liuhe LiLiuhe Li
Liuhe Li
Liuhe LiLiuhe Li
Liuhe Li
DLDuoduo Li
Duoduo Li
LTLing Tang
Ling Tang
YLYang Luo
Yang Luo
XXXiaolei Xu
Xiaolei Xu
Erosion seriously threatens the safety of high-speed rotating mechanical components in very harsh service environments, particularly for lightweight titanium alloy matrix material. In order to improve the erosion resistance of titanium alloy, TiAlSiN coatings with different phase compositions are deposited on TC6 titanium alloy using a high-power pulse magnetron sputtering discharge (HPPMS) system under various discharge voltages. The componential and microstructural evolution as well as mechanical properties of the TiAlSiN coatings are evaluated by X-ray diffraction, scanning electron microscopy, and nanoindentation, respectively. The erosion performance relative to titanium alloy is investigated by a sand blasting tester. With the increase in discharge voltage from −500 to −600 V, the peak of discharge current increases from 105 to 225 A. The prepared TiAlSiN coatings show a shift of the preferred crystallographic orientation from (220) to (200), but all of them have a dense nanocomposite structure. Their hardness (H) and elastic modulus (E) gradually increase before decreasing, arriving at maximum values of 35.34 and 360.5 GPa at −570 V. The erosion resistance of the TiAlSiN coatings dependent on the discharge voltage is consistent with the H/E ratio change. The TiAlSiN coatings prepared at −560 V exhibit the optimal erosion resistance, which is 15 times that of the TC6 substrate. The erosion behavior of the coatings is positively correlated with their hardness and toughness. Adjusting the discharge voltage of the HPPMS pulse is finally proved to be an effective way of tailoring the coating phase compositions to improve the erosion resistance of titanium alloy.

24 November 2021 in Coatings
Verified
Journal Article
Open access
PDF file
Guodong LiGuodong Li
Guodong Li
FMFei Ma
Fei Ma
ZLZhijie Li
Zhijie Li
YXYi Xu
Yi Xu
FGFangyuan Gao
Fangyuan Gao
YXYuan Xia
Yuan Xia
In this study, plasma electrolytic oxidation (PEO) was performed on Al and AlSi substrates using a pulsed direct current (DC) power source. The coating process was carried out in a Na2SiO3 electrolyte with the systematic change of pulse frequency (50–1400 Hz). The surface characteristics of the coatings were examined using scanning electron microscopy (SEM). The phase structure was characterized using X-ray diffraction (XRD). A differential scanning calorimeter (DSC) and a laser flash apparatus (LFA) were employed to test heat capacity and heat conductivity, respectively. Results showed that as the discharge frequency increased, the thermal physical properties of Al-PEO and AlSi-PEO coatings changed in different ways. At a high frequency, Al-PEO coatings had low porosity and were closed-pore structured whereas AlSi-PEO coatings had high porosity and large-size open-pore structures could be observed on their surfaces due to concentrated discharges. Based on these findings, it was found that the thermal productivity of coatings is closely correlated with the open-/closed-pore structure instead of porosity. PEO coatings with low heat capacity or low heat conductivity could be obtained with a controlled frequency.

28 June 2020 in Coatings
Verified
Journal Article
Open access
PDF file
GLGuang Li
Guang Li
YXYi Xu
Yi Xu
YXYuan Xia
Yuan Xia
A pulsed-dc (direct current) magnetron sputtering with a plasma emission monitor (PEM) system was applied to synthesize Cr-containing hydrogenated amorphous diamond-like carbon (Cr-DLC) films using a large-size industrial Cr target. The plasma emission intensity of a Cr atom at 358 nm wavelength was characterized by optical emission spectrometer (OES). C2H2 gas flow rate was precisely adjusted to obtain a stable plasma emission intensity. The relationships between Cr atom plasma emission intensity and the element concentration, cross-sectional morphology, deposition rate, microstructure, mechanical properties, and tribological properties of Cr-DLC films were investigated. Scanning electron microscope and Raman spectra were employed to analyze the chemical composition and microstructure, respectively. The mechanical and tribological behaviors were characterized and analyzed by using the nano-indentation, scratch test instrument, and ball-on-disk reciprocating friction/wear tester. The results indicate that the PEM system was successfully used in magnetron sputtering for a more stable Cr-DLC deposition process.

25 August 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Guodong LiGuodong Li
Guodong Li
GLGuang Li
Guang Li
YXYuan Xia
Yuan Xia
In this study, samples underwent plasma electrolytic oxidation (PEO) treatment using Al/Ti tracer substrates for 5, 10, 20, 35, and 55 min. The ionization states were determined using Optical Emission Spectroscopy (OES). Microstructural and elemental analyses were conducted using scanning electron microscopy equipped with energy dispersive spectrometry (SEM-EDS). The structural organization and phase composition of the coatings were characterized using X-ray diffraction (XRD) and Raman spectroscopy, respectively. The research findings indicate that the early discharge stage is dominated by discharge within the pre-deposited Al layer, which undergoes gradual oxidation along the thickness direction, while Ti (0.25 wt%) is found on the coating surface. The power increase was 56% of the total increase from min 5 to min 10 of discharge. As discharge time increased, the spectral peaks corresponding to Ti gradually became stronger and were accompanied by gradual enhancement of the crystallinity of the anatase and rutile phases within the coating. The coating surface displayed closed and semi-closed pores in the middle of the discharge. After 55 min of discharge, amorphous SiO2 was observed and Ti content on the coating surface increased to 4.59 wt%.

16 November 2015 in arXiv
Verified
Preprint
Open access
PDF file
ZCZhitong Chen
Zhitong Chen
BFBiao Feng
Biao Feng
YXYuan Xia
Yuan Xia
GLGuang Li
Guang Li
Scratch sliding tests with a ZrO2 ball and CrAlSiN films with different Si content were conducted due to CrAlSiN films having high hardness and good wear resistance. After up to 6000 cycles the specimens were analyzed by Scanning Electron Microscopy. The friction coefficient of CrAlSiN was lower than that of CrAlN film.A corresponding three-dimensional finite element model was constructed with the help of the ABAQUS to describe the mechanical response during scratch. A comparison of experimental and computational results revealed that the small elastic deformation took place in the films and substrates;the deformation friction coefficient was negligible in comparison with the Coulomb friction coefficient;and with increasing Young's modulus, the stress concentration was more obvious in CrAlSiN than in CrAlN.