Carmela Riccio

Prof. Carmela Riccio

Politechnic of Torino
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 November 2021 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
Carmela RiccioCarmela Riccio
Carmela Riccio
Marco CiveraMarco Civera
Marco Civera
OROliver Grimaldo Ruiz
Oliver Grimaldo Ruiz
PPPerla Pedullà
Perla Pedullà
MRMariana Rodriguez Reinoso
Mariana Rodriguez Reinoso
Cecilia SuraceCecilia Surace
Cecilia Surace
Different mechanical properties characterise the materials of 3D printed components, depending on the specific additive manufacturing (AM) process, its parameters, and the post-treatment adopted. Specifically, stereolithography (SLA) uses a photopolymerisation technique that creates solid components through selective solidification. In this study, 72 specimens were 3D printed using 12 commercial-grade methacrylate resins and tested under uniaxial tensile loads. The resin specimens were evaluated before and after curing. The recommended cure temperature and time were followed for all materials. The stress-strain curves measured during the testing campaign were evaluated in terms of maximum tensile strength, Young’s modulus, ductility, resilience, and toughness. The results reveal that the curing process increases the material stiffness and resistance to tensile loads. However, it was found that the curing process generally reduces the plasticity of the resins, causing a more or less marked brittle behaviour. This represents a potential limitation to the use of SLA 3D printing for structural elements which require some plasticity to avoid dangerous sudden failures.

25 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
MRMariana Rodriguez Reinoso
Mariana Rodriguez Reinoso
Marco CiveraMarco Civera
Marco Civera
VBVito Burgio
Vito Burgio
Annalisa ChiapponeAnnalisa Chiappone
Annalisa Chiappone
OROliver Grimaldo Ruiz
Oliver Grimaldo Ruiz
Cecilia SuraceCecilia Surace
Cecilia Surace
Biocompatible and biodegradable polymers represent the future in the manufacturing of medical implantable solutions. As of today, these are generally manufactured with metallic components which cannot be naturally absorbed within the human body. This requires performing an additional surgical procedure to remove the remnants after complete rehabilitation or to leave the devices in situ indefinitely. Nevertheless, the biomaterials used for this purpose must satisfy well-defined mechanical requirements. These are difficult to ascertain at the design phase since they depend not only on their physicochemical properties but also on the specific manufacturing methods used for the target application. Therefore, this research was focused on establishing the effects of the manufacturing methods on both the mechanical properties and the thermal behavior of a medical-grade copolymer blend. Specifically, Injection and Compression Molding were considered. A Poly(L-lactide-co-D,L-lactide)/Poly(L-lactide-co-ε-caprolactone) blend was considered for this investigation, with a ratio of 50/50 (w/w), aimed at the manufacturing of implantable devices for tendon repair. Interesting results were obtained.

28 January 2022 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
Carmela RiccioCarmela Riccio
Carmela Riccio
Marco CiveraMarco Civera
Marco Civera
OROliver Grimaldo Ruiz
Oliver Grimaldo Ruiz
PPPerla Pedullà
Perla Pedullà
MRMariana Rodriguez Reinoso
Mariana Rodriguez Reinoso
Cecilia SuraceCecilia Surace
Cecilia Surace
The Authors of the paper “Effects of Curing on Photosensitive Resins in SLA Additive Manufacturing”