The alloyed surface layers were produced using thin Al or AlSi20 plates, which were first diffusion bonded and then melted into the Mg substrate. The microscopic analysis showed that alloying with Al led to the formation of an Al-enriched surface layer containing a high volume fraction of an Mg17Al12 phase. Applying AlSi20, on the other hand, resulted in the formation of an Al/Si-enriched layer containing Mg2Si, Mg2Al3 and Mg17Al12 phases. The experimental results indicate that surface alloying of Mg with Al or AlSi20 using the presented method improved the properties of the material. The microhardness of the Al- and Al/Si-enriched layers was much higher than that of the substrate. Higher wear resistance was observed for the Al/Si-enriched layer. The alloyed layers provided a certain level of protection of Mg against corrosion. The specimens alloyed with Al showed better anticorrosive properties than those alloyed with AlSi20.
This paper presents the results of an analysis of the mechanical properties of the S420M steel samples collected both perpendicular and parallel to the rolling direction. The scope of the analysis included the following: a static tensile test, a hardness measurement, a low-cycle fatigue test, and a microstructure analysis of the analysed material. During the analysis, it was found that the rolling direction had little effect on the most important strength parameters determined in the static tensile test, but had a significant effect on the fatigue properties. During fatigue testing, a significant reduction in fatigue life (from 50% to almost 300%) was observed for samples perpendicular to the rolling direction. The largest reduction in fatigue life was observed at the εac = 0.25% strain level (almost 300%), while the smallest was at ε = 0.25% (50%). A comparative analysis of the results of constant-amplitude and programmed fatigue tests confirmed the validity of using accelerated life tests to determine the low-cycle fatigue properties of construction materials. The results of the experimental verification of the Palmgren–Miner linear hypothesis of fatigue damage accumulation confirmed the significant influence of the material data on the results of fatigue life calculations.
Thick (400 µm) glow-discharge nitrided layers, TiN+Ti2N + αTi(N) type, have been produced on the Ti-1Al-1Mn titanium alloy. Using a progressive thinning method, the polarization characteristics at different depths of nitrided layers have been measured. From the plots of obtained potentiodynamic polarization curves the depth profiles of characteristic anodic and cathodic currents (at potentials corresponding to (a) hydride formation, (b) hydrogen evolution, (c) primary passivation, (d) oxygen evolution and (e) secondary passivation) as well as polarization resistance have been determined in 0.5 M Na2SO4 solution acidified to pH = 2. The anomalously high slope of the polarization curves in the cathodic region has been ascribed to the formation of titanium hydride. It has been shown that outer nitrided layers (up to 25 µm) exhibit excellent acid corrosion resistance owing to strong inhibition of the anodic process by TiN phase. Corrosion resistance of deeper situated layers gradually decreases and at depths of 250–370 µm the corrosion process is accelerated by presence of TiO2 precipitations. Nitrided layers, unlike the alloy core, allow oxygen evolution on the oxy-nitrided surface at potential of +1.6 V and at more positive potentials gradual transformation of the surfacial film into TiO2 takes place. Secondary passivation on nitrided titanium is less efficient than that in the absence of Ti-N species.
The paper presents the results of experimental tests of the rolling process of Mg/Al bimetallic bars in two systems of classic passes (horizontal oval-circle-horizontal oval-circle variant I) and modified (multi-radial horizontal oval-multi-radial vertical oval-multi-radial horizontal oval-circle-variant II). The feedstock in the form of round bimetallic bars with a diameter of 22 mm and 30% of the outer aluminum layer was made through explosive welding. The bimetallic bars consisted of an AZ31 magnesium core and a 1050A aluminum outer layer. Bars with a diameter of 17 mm were obtained as a result of rolling in four passes. The rolling process in the passes was conducted at two temperatures of 300 and 400 °C. Based on the analysis of the test results, it was found that the use of modified passes and a lower rolling temperature (300 °C) ensures a more homogenous distribution of the plating layer around the circumference of the core and results in an even grain decreasing, which improves the corrosion resistance of bimetallic bars compared to rolling bars in a classic system of passes and at a higher temperature (400 °C).
This study aims to analyze the influence of the rolling process on the microstructure and corrosion properties of the Mg/Al bimetallic bars obtained by the explosive welding method. The bars investigated were rolled using two different types of rolling: classical rolling (Variant I) and modified rolling (Variant II). Two different temperatures (300 °C and 400 °C) for each of the variables were applied as well. In this study, rods with an aluminum plating layer constituting 16.8% of the cross-sectional area and an average thickness of about 0.93 mm were investigated. Based on the revealed results, it was found that after the rolling process, the material shows clearly lower values of both icor and current in the passive range. In the joint zone of Mg/Al rods rolled at 400 °C, Al3Mg2 and Mg17Al12 intermetallic phases are distinguished, localized next to the Mg core, and characterized by columnar, coarser grains. In the transition zone closer to the Al layer, only the Al3Mg2 phase is revealed, characterized by a refined, small grain size.