Andrzej Dziadoń

Andrzej Dziadoń

Auto-generated profile, based on publicly available information

Andrzej Dziadoń

Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, Al. Tysiąclecia P.P. 7, 25-314 Kielce, Poland

Research Focus & Metrics

Academic Career Length

41Years (1986-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2011 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
ADA. Dziadoń
A. Dziadoń
RMR. Mola
R. Mola
LBL. Błaż
L. Błaż
Formation of Layered Mg/Eutectic Composite Using Diffusional Processes at the Mg-Al Interface: A processing technique has been developed to produce a layered magnesium-intermetallic compound light composite from elemental magnesium and aluminium sheets. Structural examination and measurements of transition layer grown at the magnesium-aluminium interface at high annealing temperature were performed. It was found using Mg/Al diffusion couple that solid state diffusion results in development of Al3Mg2and Mg17Al12intermetallic compounds, which are separated into two sublayers. The rate of the layer growth substantially increases with the appearance of the liquid phase at the Mg-Al interface. The microstructure resulted from the partial solidification contains an eutectic composed of Mg17Al12intermetallic compound and solid solution aluminium in magnesium. The structural processes, which transform the magnesium-aluminium interface, can be applied for fabrication of layered magnesium-eutectic composites. Alternately stacked magnesium and aluminium sheets, formed into a packet, were heated until aluminium was exhausted throughout the course of the Mg-Al reaction with the liquid phase contribution. As a result, the composite containing residual magnesium and layers of eutectic mixture (Mg17Al12and solid solution of aluminium in magnesium) was obtained. Rapid solidification resulted in fine-grained eutectic microstructure development. Using the presented method, composites with required thickness ratio of magnesium and the eutectic layers can be obtained by choosing appropriate thickness ratio of starting magnesium and aluminium sheets.

1 August 2016 in Materials Characterization
Verified
Journal Article
Closed access
ADAndrzej Dziadoń
Andrzej Dziadoń
RMRenata Mola
Renata Mola
LBLudwik Błaż
Ludwik Błaż

15 July 2007 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
MKMarek Konieczny
Marek Konieczny
ADA. Dziadoń
A. Dziadoń

1 March 2016 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
RMR. Mola
R. Mola
TBTomasz Bucki
Tomasz Bucki
ADA. Dziadoń
A. Dziadoń
Al-enriched layer was formed on a magnesium substrate with use of casting. The magnesium melt was cast into a steel mould with an aluminium insert placed inside. Different conditions of the casting process were applied. The reaction between the molten magnesium and the aluminium piece during casting led to the formation of an Al-enriched surface layer on the magnesium substrate. The thickness of the layer was dependent on the casting conditions. In all fabricated layers the following phases were detected: a solid solution of Mg in Al, Al3Mg2, Mg17Al12 and a solid solution of Mg in Al. When the temperature of the melt and the mould was lower (variant 1 – 670°C and 310°; variant 2 – 680°C and 310°C, respectively) the unreacted thin layer of aluminium was observed in the outer zone. Applying higher temperatures of the melt (685°C) and the mould (325°C) resulted in deep penetration of aluminium into the magnesium substrate. Areas enriched in aluminium were locally observed. The Al-enriched layers composed mainly of Mg-Al intermetallic phases have hardness from 187-256 HV0.1.

30 June 2016 in Surface Engineering
Verified
Journal Article
Closed access
RMRenata Mola
Renata Mola
ADAndrzej Dziadoń
Andrzej Dziadoń
Karina Jagielska-WiaderekKarina Jagielska-Wiaderek
Karina Jagielska-Wiaderek
The alloyed surface layers were produced using thin Al or AlSi20 plates, which were first diffusion bonded and then melted into the Mg substrate. The microscopic analysis showed that alloying with Al led to the formation of an Al-enriched surface layer containing a high volume fraction of an Mg17Al12 phase. Applying AlSi20, on the other hand, resulted in the formation of an Al/Si-enriched layer containing Mg2Si, Mg2Al3 and Mg17Al12 phases. The experimental results indicate that surface alloying of Mg with Al or AlSi20 using the presented method improved the properties of the material. The microhardness of the Al- and Al/Si-enriched layers was much higher than that of the substrate. Higher wear resistance was observed for the Al/Si-enriched layer. The alloyed layers provided a certain level of protection of Mg against corrosion. The specimens alloyed with Al showed better anticorrosive properties than those alloyed with AlSi20.

1 March 2017 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
RMR. Mola
R. Mola
TBTomasz Bucki
Tomasz Bucki
ADA. Dziadoń
A. Dziadoń
This paper discusses the joining of AZ91 magnesium alloy with AlSi17 aluminium alloy by compound casting. Molten AZ91 was cast at 650°C onto a solid AlSi17 insert placed in a steel mould under normal atmospheric conditions. Before casting, the mould with the insert inside was heated up to about 370°C. The bonding zone forming between the two alloys because of diffusion had a multiphase structure and a thickness of about 200 μm. The microstructure and composition of the bonding zone were analysed using optical microscopy, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results indicate that the bonding zone adjacent to the AlSi17 alloy was composed of an Al3Mg2intermetallic phase with not fully consumed primary Si particles, surrounded by a rim of an Mg2Si intermetallic phase and fine Mg2Si particles. The bonding zone near the AZ91 alloy was composed of a eutectic (an Mg17Al12intermetallic phase and a solid solution of Al and Si in Mg). It was also found that the compound casting process slightly affected the AZ91 alloy microstructure; a thin layer adjacent to the bonding zone of the alloy was enriched with aluminium.