This paper deals with the description, measurement, and use of electromagnetic properties of ferromagnetic fibres used as dispersed fibre reinforcement in composite mixtures. Firstly, the fibres’ magnetic properties are shown, and a method of measuring the hysteresis loop of fibres is proposed. The results from the measurements are presented and a discussion of the influence of measured parameters on the fibres’ orientation in a magnetic field is performed. Furthermore, methods of non-destructive estimation, of their amount and orientation in the composite specimens, are discussed. The main experimental goal of this paper is to show the relationship between this non-destructive method’s results and the destructive flexural strength measurements. The method is sensitive enough to provide information related to fibre reinforcement.

The static response of ballistic panels and also its resistance to blast and ballistic impact is investigated in the framework of this study. By connecting individual ballistic panels together, the protective barrier can be constructed. The protective barrier can be featured as a system with high mobility and versatility that is achieved by linking basic interlocking plate elements together. The resulting protective barrier can be shaped according to many possible scenarios in a wall with various possible opening angles and a small post with the tetragonal base or a larger post with the hexagonal ground plan. The material solution of the protective barrier benefits from the application of ultra-high-performance fibre-reinforced cement-based composites (UHPFRCC), which meets the requirements for enhanced resistance against extreme loads such as blast or impact. Besides, by using UHPFRCC, thin and slender design can be adopted, which is advantageous in many ways. Slender design results in a lower weight, allowing for easy manipulation and replacement. To verify the behavior of the panels, the proposed barrier was subjected to various loadings at different strain rates. The experimental campaign demonstrated that the protective barrier has a reasonable load-bearing capacity and also sufficient resistance against projectile impact and blast effects.

Ultra-high-performance steel-fibre-reinforced concrete (UHP-SFRC) is a technologically advanced composite with a high ability to absorb and dissipate mechanical energy. This work investigates the possibility of increasing ballistic resistance by adding different percentages of corundum and basalt aggregate into this type of concrete. The most common type of ammunition, a 7.62 mm × 39 mm calibre with a full-metal jacket and a mild-steel core (FMJ-MSC), was used to test all samples. The size of the damage and the mode of failure were determined using a 3D scanner operating on the principle of photogrammetry. The experimental campaign showed that the addition of basalt and, especially, corundum aggregate has a positive effect on ballistic resistance. In particular, the increase in compressive strength and the slight decrease in depth of penetration (DOP) was observed in the case of the usage of the corundum aggregate.

Ultra-high performance fiber-reinforced concrete (UHPFRC) can be used to build lightweight bulletproof structures because even its thin layer can prevent projectile perforation. UHPFRC is significantly less expensive than other armor materials such as steel, Kevlar, nylon, or ceramic. It has good volume stability and very low porosity, which makes it highly durable and provides sufficient resistance to freeze-thaw cycles. However, when a projectile hits a thin UHPFRC structure, the fragments can break off. The fragments can injure people or damage property in the vicinity of the structure. To address this problem, we have developed a new generation of sandwich structures consisting of a UHPFRC core, a fiber-reinforced epoxy composite, and an elastomeric coating. UHPFRC and composite provide penetration resistance. Composite and elastomer reduce fragmentation of UHPFRC. By properly designing these three materials, their thickness, and their position in the sandwich structure, lightweight and affordable bulletproof panels can be produced. This contribution presents such a structure and subjects it to ballistic testing according to European and American standards. It is shown that the additional layers eliminate the formation of rear fragments after projectile impact and reduce the panel weight by 13% compared to the panel made entirely of UHPFRC. Due to their unique shape, the panels can be combined to form a mobile and modular protective barrier. The barrier can take the form of a freestanding wall with various opening angles, or an outpost with a square or hexagonal base. It can be moved and assembled quickly by just two people.

Classified information is information of vital importance to the State, which must be protected against disclosure, misuse, damage, unauthorized reproduction, destruction, loss or theft in the interest of the State. At present, there are four levels of classification. For each classification level, precise requirements are laid down for the material of the walls, partitions and ceilings of the rooms in which classified information is stored. Several types of materials are defined for each classification level. The objective of this study was to test and determine whether the different types of materials proposed for the Confidential level meet the same level of resistance. A drop weight test via pendulum was used to determine the resistance. A 50 kg weight was used to break through a 60 × 100 cm sample. The impact of the weight was on the exact center of the sample. The result of the tests was that to break through samples of different materials, large differences in the drop height of the weight were required. The most resistant was the specimen made of reinforced concrete, which required 3 impacts from a height of 80 cm to break through. On the contrary, the least resistant were the specimens made of masonry of autoclaved aerated concrete, where after 2 falls from a height of 5 cm, the sample broke into 2 parts.