Emine Feyza Sukur

Dr. Emine Feyza Sukur


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 February 2024 in Composites Part B: Engineering
Verified
Journal Article
Closed access
ESEmine Feyza Sukur
Emine Feyza Sukur
SESelen Elimsa
Selen Elimsa
VEVolkan Eskizeybek
Volkan Eskizeybek
AAAhmet Avci
Ahmet Avci


27 April 2022 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
ESEmine Feyza Sukur
Emine Feyza Sukur
SESinem Elmas
Sinem Elmas
MSMahsa Seyyednourani
Mahsa Seyyednourani
VEVolkan Eskizeybek
Volkan Eskizeybek
MYMehmet Yildiz
Mehmet Yildiz
HSHatice S. Sas
Hatice S. Sas


11 May 2023 in Journal of Applied Polymer Science
Verified
Journal Article
Open access
ESEmine Feyza Sukur
Emine Feyza Sukur
SESinem Elmas
Sinem Elmas
VEVolkan Eskizeybek
Volkan Eskizeybek
HSHatice S. Sas
Hatice S. Sas
MYMehmet Yildiz
Mehmet Yildiz
During the service life of aerospace‐grade composites, process parameters and process‐induced defects may become crucial. Most studies in this field have mainly focused on the relationship between process‐induced defects and mechanical performance. However, the potential impact of process parameters and process‐induced defects on the service life of composites serving under severe service conditions has received little attention. In this work, the effects of hydrothermal conditioning on the mechanical performance of carbon fiber/polyether ketone ketone (CF/PEKK) composites are examined, along with the correlation between automated fiber placement (AFP) process parameters and process‐induced defects. For this, gap and overlap defects integrated CF/PEKK laminates were exposed to a long‐term (90 days) hot‐wet aging environment to simulate the actual service conditions. Defect‐induced composite samples reached saturation point at the end of 30 days with a mass gain of 0.2 wt%. The aging process resulted in an increase in the degree of crystallization by almost 14% without a change in the chemical structure, indicating the postcrystallization of the PEKK matrix. Even though the thermo‐mechanical performance diminished (~25%) with the aging process, storage modulus was slightly affected by process parameters and process‐induced defects. Considering the flexural and shear test results after the aging process, the impact of gap and overlap defects on the service life of AFP composites can be minimized with higher compaction forces (600 N) and lower lay‐up speeds (0.1 m/s).

7 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
MAMuhammed Hasan Arikan
Muhammed Hasan Arikan
FEFatih Eroglu
Fatih Eroglu
VEVolkan Eskizeybek
Volkan Eskizeybek
ESEmine Feyza Sukur
Emine Feyza Sukur
MYMehmet Yildiz
Mehmet Yildiz
HSHatice S. Sas
Hatice S. Sas
Aerospace-grade composite parts can be manufactured using Vacuum Bag Only prepregs through an accurate process design. Quality in the desired part can be realized by following process modeling, process optimization, and validation, which strongly depend on a primary and systematic material characterization methodology of the prepreg system and material constitutive behavior. The present study introduces a systematic characterization approach of a Vacuum Bag Only prepreg by covering the relevant material properties in an integrated manner with the process mechanisms of fluid flow, consolidation, and heat transfer. The characterization recipe is practiced under the categories of (i) resin system, (ii) fiber architecture, and (iii) thermal behavior. First, empirical models are successively developed for the cure-kinetics, glass transition temperature, and viscosity for the resin system. Then, the fiber architecture of the uncured prepreg system is identified with X-ray tomography to obtain the air permeability. Finally, the thermal characteristics of the prepreg and its constituents are experimentally characterized by adopting a novel specimen preparation technique for the specific heat capacity and thermal conductivity. Thus, this systematic approach is designed to provide the material data to process modeling with the motivation of a robust and integrated Vacuum Bag Only process design.