This paper proposes an advanced Pareto-front non-dominated sorting multi-objective particle swarm optimization (Advanced-PFNDMOPSO) method for optimal configuration (placement and sizing) of distributed generation (DG) in the radial distribution system. The distributed generation consists of single and multiple numbers of active power DG, reactive power DG and simultaneous placement of active-reactive power DG. The optimization problem considers two multi-objective functions, i.e., power loss reduction and voltage stability improvements with voltage profile and power balance as constraints. First, the numerical output results of objective functions are obtained in the Pareto-optimal set. Later, fuzzy decision model is engendered for final selection of the compromised solution. The proposed method is employed and tested on standard IEEE 33 bus systems. Moreover, the results of proposed method are validated with other optimization algorithms as reported by others in the literature. The overall outcome shows that the proposed method for optimal placement and sizing gives higher capability and effectiveness to the final solution. The study also reveals that simultaneous placement of active-reactive power DG reduces more power losses, increases voltage stability and voltage profile of the system.

In recent years, renewable types of distributed generation in the distribution system have been much appreciated due to their enormous technical and environmental advantages. This paper proposes a methodology for optimal placement and sizing of renewable distributed generation(s) (i.e., wind, solar and biomass) and capacitor banks into a radial distribution system. The intermittency of wind speed and solar irradiance are handled with multi-state modeling using suitable probability distribution functions. The three objective functions, i.e., power loss reduction, voltage stability improvement, and voltage deviation minimization are optimized using advanced Pareto-front non-dominated sorting multi-objective particle swarm optimization method. First a set of non-dominated Pareto-front data are called from the algorithm. Later, a fuzzy decision technique is applied to extract the trade-off solution set. The effectiveness of the proposed methodology is tested on the standard IEEE 33 test system. The overall results reveal that combination of renewable distributed generations and capacitor banks are dominant in power loss reduction, voltage stability and voltage profile improvement.

A compound parabolic concentrator (CPC) is a non-imaging device generally used in PV, thermal, or PV/thermal hybrid systems for the concentration of solar radiation on the target surface. This paper presents the geometric design, statistical modeling, parametric analysis, and geometric optimization of a two-dimensional low concentration symmetric compound parabolic concentrator for potential use in building-integrated and rooftop photovoltaic applications. The CPC was initially designed for a concentration ratio of “2×” and an acceptance half-angle of 30°. A MATLAB code was developed in-house to provoke the CPC reflector’s profile. The height, aperture width, and concentration ratios were computed for different acceptance half-angles and receiver widths. The interdependence of optical concentration ratio and acceptance half-angle was demonstrated for a wide span of acceptance half-angles. The impact of the truncation ratio on the geometric parameters was investigated to identify the optimum truncation position. The profile of truncated CPC for different truncation positions was compared with full CPC. A detailed statistical analysis was performed to analyze the synergistic effects of independent design parameters on the responses using the response surface modeling approach. A set of optimized design parameters was obtained by establishing specified optimization criteria. A 50% truncated CPC with an acceptance half-angle of 21.58° and receiver width of 193.98 mm resulted in optimum geometric dimensions.

Microgrids help to achieve power balance and energy allocation optimality for the defined load networks. One of the major challenges associated with microgrids is the design and implementation of a suitable communication-control architecture that can coordinate actions with system operating conditions. In this paper, the focus is to enhance the intelligence of microgrid networks using a multi-agent system while validation is carried out using network performance metrics i.e., delay, throughput, jitter, and queuing. Network performance is analyzed for the small, medium and large scale microgrid using Institute of Electrical and Electronics Engineers (IEEE) test systems. In this paper, multi-agent-based Bellman routing (MABR) is proposed where the Bellman–Ford algorithm serves the system operating conditions to command the actions of multiple agents installed over the overlay microgrid network. The proposed agent-based routing focuses on calculating the shortest path to a given destination to improve network quality and communication reliability. The algorithm is defined for the distributed nature of the microgrid for an ideal communication network and for two cases of fault injected to the network. From this model, up to 35%–43.3% improvement was achieved in the network delay performance based on the Constant Bit Rate (CBR) traffic model for microgrids.

This paper presents a compensating system for the harmonics and the reactive power using four-leg shunt active power filter (SAPF) in a three-phase four-wire distribution network and aims to minimize the harmonics and neutral current. Two control approaches p-q theory based hysteresis current control and load current detection based hysteresis current control are proposed. To validate the compensation performance of SAPF a distribution network with nonlinear loads is simulated using MATLAB/Simulink software. Simulation results are presented to assess the performance of SAPF to minimize the total harmonics distortion (THD) and neutral current, as well as to compensate the reactive power.