Diamond offers great potential for use as a thermal spreader in various applications, including power electronics and radio-frequency (RF) applications. However, to be used as an efficient thermal spreader, the atomically smooth surface of the diamond is critical to be bonded with chips. Herein, a polishing technique for a 2-inch diameter wafer-scale bulk polycrystalline diamond substrate is proposed. In this work, 350 m thick polycrystalline diamond is grown by the microwave plasma-assisted chemical vapor deposition (MPACVD) technique on a Si substrate at a growth rate of 8 µm/h. Thereafter, a three-step polishing process was applied to achieve an atomically smooth surface, consisting of grinding using a diamond slurry with an iron plate, ICP etching using the SF6 gas, and final mechanical polishing using a resin-bonded diamond wheel. Surface roughness of diamond characterized by atomic force microscopy showed the significantly reduced from 900 nm to 0.3 nm. Hence, this study provide the practical methods for obtaining atomically smooth diamond films suitable for thermal management in various areas including power electronics and RF devices.
Large-area, continuous monolayer WS2 exhibits great potential for future micro-nanodevice applications due to its special electrical properties and mechanical flexibility. In this work, the front opening quartz boat is used to increase the amount of sulfur (S) vapor under the sapphire substrate, which is critical for achieving large-area films during the chemical vapor deposition processes. COMSOL simulations reveal that the front opening quartz boat will significantly introduce gas distribute under the sapphire substrate. Moreover, the gas velocity and height of substrate away from the tube bottom will also affect the substrate temperature. By carefully optimizing the gas velocity, temperature, and height of substrate away from the tube bottom, a large-scale continues monolayered WS2 film was achieved. Field-effect transistor based on the as-grown monolayer WS2 showed a mobility of 3.76 cm2V−1 s−1 and ON/OFF ratio of 106. In addition, a flexible WS2/PEN strain sensor with a gauge factor of 306 was fabricated, showing great potential for applications in wearable biosensors, health monitoring, and human–computer interaction.
12 January 2016 in Journal of Physics D: Applied Physics
Density functional theory calculations have been performed to elucidate the detailed evolution of band structures in MoS2-based homo- and heterobilayers. By constructing the energy-band alignments we observed that biaxial tensile and compressive strain in the constituent transition-metal dichalcogenide (TMD) monolayer shifts the states at the KC, QC, and KV points down and up, respectively, while the states at the ΓV point are almost unaltered. In contrast, interlayer coupling tends to modify the states at the ΓV and QC points by splitting the band-edge states of two strained or unstrained constituent TMD monolayers, while it does not affect the states at the KC and KV points. Considering the combined actions of strain and interlayer coupling, the relevant electronic parameters, especially the detailed evolution processes, of the band structures of the investigated bilayer systems can be clearly described. When further applying the extra biaxial strain to the three bilayer systems, it is found that energy differences ΔE(KC − QC) and ΔE(KV − ΓV) decrease linearly as the increasing of the biaxial strain. According to the varying trends of ΔE(KC − QC) and ΔE(KV − ΓV), MoS2 bilayer will maintain the indirect-bandgap character under any compressive or tensile strain. Differently, WS2/MoS2 heterobilayer transforms interestingly to the direct-bandgap material under the strain from −1.6% to −1.2% with the valence band maximum and conduction band minimum located at the KC and KV point respectively. The direct-to-indirect bandgap transition can be obtained for the WSe2/MoS2 heterobilayer when applying much larger extra tensile or compressive strain. The results offer an effective route to verify and tailor the electronic properties of TMD homo- and heterostructures and can be helpful in evaluating the performance of TMD-based electronic devices.
The interfacial properties of MoS2/4H-SiC heterostructures were studied by combining first-principles calculations and X-ray photoelectron spectroscopy. Experimental (theoretical) valence band offsets (VBOs) increase from 1.49 (1.46) to 2.19 (2.36) eV with increasing MoS2 monolayer (1L) up to 4 layers (4L). A strong interlayer interaction was revealed at 1L MoS2/SiC interface. Fermi level pinning and totally surface passivation were realized for 4H-SiC (0001) surface. About 0.96e per unit cell transferring forms an electric field from SiC to MoS2. Then, 1L MoS2/SiC interface exhibits type I band alignment with the asymmetric conduction band offset (CBO) and VBO. For 2L and 4L MoS2/SiC, Fermi level was just pinning at the lower MoS2 1L. The interaction keeps weak vdW interaction between upper and lower MoS2 layers. They exhibit the type II band alignments and the enlarged CBOs and VBOs, which is attributed to weak vdW interaction and strong interlayer orbital coupling in the multilayer MoS2. High efficiency of charge separation will emerge due to the asymmetric band alignment and built-in electric field for all the MoS2/SiC interfaces. The multiple inter-facial interactions provide a new modulated perspective for the next-generation electronics and optoelectronics based on the 2D/3D semiconductors heterojunctions.
We investigate the electric-field-dependent optical properties and electronic behaviors of GaS monolayer by using the first-principles calculations. A reversal of the dipole transition from E//c to E⊥c anisotropy is found with a critical external electric field of about 5 V/nm. Decomposed projected band contributions exhibit asymmetric electronic structures in GaS interlayers under the external electric field, which explains the evolution of the absorption preference. Spatial distribution of the partial charge and charge density difference reveal that the strikingly reversed optical anisotropy in GaS ML is closely linked to the additional crystal field originated from the external electric field. These results pave the way for experimental research and provide a new perspective for the application of the monolayer GaS-based two-dimensional electronic and optoelectronic devices.