Photocatalysis is a remarkable methodology that is popular and applied in different interdisciplinary research areas such as the degradation of hazardous organic contaminants in wastewater. In recent years, clay-based photocatalyst composites have attracted significant attention in the field of photocatalysis owing to their abundance, excellent light response ability, and stability. This review describes the combination of clay with focusing photocatalysts such as TiO2, g-C3N4, and Bi-based compounds for degrading organic pollutants in wastewater. Clay-based composites have more active surface sites, resulting in inhibited photocatalyst particle agglomeration. Moreover, clay enhances the creation of active radicals for organic pollutant degradation by separating photogenerated electrons and holes. Thus, the functions of clay in clay-based photocatalysts are not only to act as a template to inhibit the agglomeration of the main photocatalysts but also to suppress charge recombination, which may lengthen the electron–hole pair’s lifespan and boost degrading activity. Moreover, several types of clay-based photocatalysts, such as the clay type and main photocatalyst, were compared to understand the function of clay and the interaction of clay with the main photocatalyst. Thus, this study summarizes the recent clay-based photocatalysts for wastewater remediation and concludes that clay-based photocatalysts have considerable potential for low-cost, solar-powered environmental treatment.
Cu-HyS-urea and Cu-HyS-NaOH, which are hydrotalcite-like copper hydroxyl salts, were prepared by two different methods, urea hydrolysis and precipitation, respectively. Both synthesis methods provided the successful formation of a copper hydroxyl salt, Cu2(OH)3NO3. From XRD and UV-DRS results, the product from the urea hydrolysis methods (Cu-HyS-urea) displayed higher crystallinity, small bandgap energy (Eg), and high light absorption ability because of some intercalated carbonate anions. For the Cr(VI) removal test, the Cu-HyS-NaOH showed superior adsorption of Cr(VI) than Cu-HyS-urea due to a higher specific surface area, confirmed by BET analysis. However, the Cu-HyS-urea presented higher photocatalytic Cr(VI) reduction under light irradiation than Cu-HyS-NaOH, owing to narrow Eg, less recombination, and a high transfer of the photogenerated charge carriers, proven by the results from photoluminescence, photocurrent density, and electrochemical impedance spectroscopy. Thus, this work provides a new function of the hydrotalcite-like copper hydroxyl salts (Cu-HyS-urea and Cu-HyS-NaOH) that can be utilized not only for adsorption of Cr(VI) but also as photocatalysts for Cr(VI) reduction under light irradiation.
The Fe(III)-doped montmorillonite (Mt)/TiO2 composites were fabricated by adding Fe(III) during or after the aging of TiO2/Ti(OH)4 sol–gel in Mt, named as xFe-Mt/(1 − x)Fe-TiO2 and Fe/Mt/TiO2, respectively. In the xFe-Mt/(1 − x)Fe-TiO2, Fe(III) cations were expected to be located in the structure of TiO2, in the Mt, and in the interface between them, while Fe(III) ions are physically adsorbed on the surfaces of the composites in the Fe/Mt/TiO2. The narrower energy bandgap () lower photo-luminescence intensity were observed for the composites compared with TiO2. Better photocatalytic performance for phenol degradation was observed in the Fe/Mt/TiO2. The 94.6% phenol degradation was due to greater charge generation and migration capacity, which was confirmed by photocurrent measurements and electrochemical impedance spectroscopy (EIS). The results of the energy-resolved distribution of electron traps (ERDT) suggested that the Fe/Mt/TiO2 possessed a larger amorphous rutile phase content in direct contact with crystal anatase than that of the xFe-Mt/(1 − x)Fe-TiO2. This component is the fraction that is mainly responsible for the photocatalytic phenol degradation by the composites. As for the xFe-Mt/(1 − x)Fe-TiO2, the active rutile phase was followed by isolated amorphous phases which had larger () and which did not act as a photocatalyst. Thus, the physically adsorbed Fe(III) enhanced light adsorption and avoided charge recombination, resulting in improved photocatalytic performance. The mechanism of the photocatalytic reaction with the Fe(III)-doped Mt/TiO2 composite was proposed.