Measuring the low carbon performance of buildings is a crucial method for achieving the construction industry's strategic goal of “double carbon.” The carbon emission factor calculation approach proposed by the IPCC is utilized to create a carbon emission calculation model for a steel-concrete composite structure bridge across its whole life cycle. The discount rate is used to determine the dynamic carbon emissions of the steel-concrete composite structural bridge, which are then compared to the static carbon emissions. The carbon strength of the bridge is evaluated using a fuzzy comprehensive technique. The application analysis is conducted on the basis of a steel-concrete composite construction bridge in Beijing. According to the findings, carbon emissions are primarily concentrated during the preparation, production, and operation of building materials. The bridge's static and dynamic carbon emissions are 103.966 and 1378.674 ktCO 2 e, respectively. After material recovery, the values are 95.141 ktCO 2 e and 1107.751 ktCO 2 e, respectively. The ratio of dynamic and static carbon emissions ranges from 7 to 34, highlighting the significance of temporal value. After recycling the components, the bridge's static carbon strength dropped from 2.565 to 2.353, while its dynamic carbon strength fell from 2.422 to 2.210, both of which were medium carbon strengths. The model proposed in this study can successfully examine the carbon emissions and strength of bridges from both environmental and economic perspectives, and it can be used to select more environmentally friendly building materials and construction methods to increase bridge efficiency. It also provides valuable data assistance for the establishment and execution of environmental protection measures, thereby promoting the industry's long-term sustainable development.
This paper introduces a novel electromagnetic optimization technique using Taguchi method. To illustrate this technique, a linear antenna array is optimized to realize a null control pattern and a sector beam pattern. It is found that Taguchi method is easy to implement and it converges to the desired patterns quickly. This method is a good candidate for optimizing EM applications
This paper presents an investigation on strong-acid relations between corrosion rate and corrosion time in 30 studs, dipped into 36% industrial hydrochloric acid through 0.5 h, 1 h, 2 h, 4 h, 8 h, 12 h, 24 h, 48 h, and 72 h, respectively. These corroded studs are performed tensile tests to study failure mode and stress-strain curves in studs with different corrosion time. Thereafter, a 3-D finite element is established through computer program to validate test results, and then analyze mechanical properties along with failure mode of studs exposed to strong-acid corrosion. The analysis results show that the failure mode gradually changes from ductile-damage state to brittle-damage state. The corrosion rates present a non-linear elevation with an increase of strong-acid-corrosion time. The nominal yield strength, the nominal ultimate strength, and the elongation in the corroded studs exhibit a fast-downward trend when increasing corrosion time. However, the degradation of elastic modulus turn into a slow step and the yield strength ratio in studs tends to be steady. The J-C model (Johnson-Cook Constitutive) with updated coefficients can be applied to reflect the constitutive relations in studs after strong-acid corrosion under quasi-static tension conditions. Further, this model can simulate stress flows within studs after strong-acid corrosion. This research results can provide a guide for long-lifetime construction and safe maintenance in steel structural bridge.
9 May 2022 in Advances in Materials Science and Engineering
In this work, a mechanical degradation of weathering steel and carbon steel caused by strong acid corrosion has been studied in order to clarify the threat of industrial acid vehicle leakage to steel structure bridge. Twenty-seven specimens of Q345 weathering steel plates and Q345 carbon steel plates were immersed in a 36 hydrochloric acid solution at room temperature, with the corrosion time being 0h, 1h, 2h, 4h, 8h, 12h, 24h, 48h, and 72h, respectively. Subsequently, the obtained specimens were subjected to a uniaxial tensile test to determine the stress-strain curves. The surface morphology was studied by the noncontact surface topography instrument DSX500. By analyzing the degree of mechanical degradation, the constitutive models of test steels under strong acid corrosion were established. The analysis of results shows that the corrosion rate of carbon steel is higher than that of weathering steel. After 72 hours of corrosion, the mass loss rate of carbon steel and weathering steel was 4.77 and 4.30, respectively. The maximum corrosion pit depth of carbon steel was 25.52μm higher than that of weathering steel. The constitutive models were in good agreement with the test results, and the resistance to corrosion degradation and deformation of the weathering steel was higher compared to the carbon steel. The results can serve as a guideline for designing steel constructions of improved durability.
16 June 2022 in Mathematical Problems in Engineering
This study investigated the effect of corrosion pits on the mechanical degradation of steel Q345 under strong acid corrosion. The experiment on a total of 27 steel Q345 specimens corroded by 36 industrial hydrochloric acid for 0h, 1h, 2h, 4h, 8h, 12h, 24h, 48h, and 72h, respectively, is conducted to study failure mode and stress-strain curves. After that, a noncontact topography scanner (DSX500) scanned geometric parameters of corrosion pits in steel Q345 to establish its mechanical degradation. The surface morphology and the corresponding degradation law of corroded steel are also revealed. In addition, the steel plastic fracture criterion taking into account equivalent plastic fracture strain and average stress triaxiality T is adopted to propose the uniform pit model. The analysis results show that the failure mode gradually changes from ductile to brittle. It is noted that the depth and relative size of the corrosion pit are the main factors affecting the increase of the maximum pit coefficient. Further, FEM based on uniform corrosion pits is found by the flexible damage evolution criterion. Its calculation results are entirely consistent with experimental results, indicating that this model can mirror the surface morphology of steel suffering strong corrosion, and simulated accurately stress flow law and necking failure of strong corrosion steel. The proposed criterion is validated with verification results and can provide good references for the design of steel bridges under strong corrosion.
Deformation Prediction and Analysis of Soft Rock Roadway with High Altitude and Large Buried Depth Based on Particle Swarm Optimization LSTM Model: Deformation prediction is an important basis for roadway information construction, especially for soft rock roadway at high altitude and large buried depth, whether the deformation of roadway surrounding rock can be effectively and accurately predicted is an important basis for judging the stability of roadway surrounding rock. However, at present, the research on the informatization construction of the roadway is not in-depth, and the intelligent prediction technology for the deformation of the surrounding rock of the roadway is still in its infancy, and the accuracy of deformation prediction is also low. Therefore, based on the research of domestic and foreign researchers, in order to solve the breakthrough of related technology, this paper puts forward the deformation prediction and control technology of high altitude and deep buried soft rock roadway based on a neural network model. This method is based on the traditional prediction model and is replaced by the neural network, so as to improve the problems of low accuracy and large prediction deviation in the related deformation prediction of the traditional prediction model. At the same time, aiming at the problem of poor local weight and network search ability, an improved method using particle swarm optimization algorithm is proposed, which effectively considers the influence of local and global factors on the combined weight. Finally, the improved deformation prediction model of high altitude and deep buried soft rock roadway based on particle swarm optimization LSTM model is applied to an engineering example and compared with the traditional model to explore its feasibility and effectiveness. The results show that the prediction model has higher prediction accuracy than the traditional prediction model, and the relative deviation of the prediction results is controlled within 2. At the same time, compared with other models (BP neural network model), it has relatively higher accuracy and stability. The research results can provide a new idea for the deformation prediction of soft rock roadway with high altitude and deep burial.