Modular input-parallel output-serial (IPOS) DC-DC converter is becoming a crucial solution for high-voltage applications due to its flexible combination form without switching device pressure limitation. It requires high efficiency, fast response, and wide-range output for broader applications. However, the existing solutions cannot simultaneously meet all these requirements. This paper proposes a new hybrid structure with interleaved LLC converters and a DAB converter. The interleaved LLC converters provide the most output voltage with fixed switching frequency and duty cycle, while the DAB converter regulates the output voltage. The wide range output is achieved by switching the LLC converter module and continuously adjusting the output voltage of the DAB converter. Furthermore, a switching control method based on the sliding-mode variable structure is proposed to achieve a smooth and fast output voltage response during the switching process. Finally, a 0.3/0.9-1.8kV, 2kW experimental platform is established to verify the proposed converter's effectiveness and advantages.
11 June 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Owing to the integration and utilization of the parasitic capacitance of the transformer, the LCC resonant converters with a capacitive output filter are widely used in high-voltage power supplies for microwave generation, X-ray, ion implantation, and other fields. However, it is challenging for the LCC to maintain high efficiency in a wide output voltage range. In this article, an optimal control coordinate trajectories (OCCTs) based phase-shift pulse-frequency (PS-PFM) control method is proposed to achieve high efficiency by reducing the switching frequency range and the turn-off current. With the normalized time-domain analysis, the operation stage trajectories of LCC and their boundary conditions under the PS-PFM control are derived. Based on this, the OCCTs of the switching frequency and the duty cycle at different voltage gains are precisely calculated. By associating the duty cycle with the switching frequency and the output voltage gain through a fitted equation based on the OCCTs data, the proposed PS-PFM control strategy can adaptively adjust the optimal duty cycle, simplifying one of the control freedom degrees. Then, an optimization design algorithm for the resonant network parameter is proposed to reduce the conduction loss of LCC. Finally, a 10-20 kV/15 kW LCC resonant high voltage power supply prototype is built to verify the feasibility of the proposed control strategy.
6 December 2022 in IEEE Transactions on Industrial Electronics
High voltage electric field power supply with a wide output voltage range is widely used in microwave generating, X-ray, ion implantation, and other fields. However, the existing high voltage power supplies cannot meet the demand of wide voltage regulation range for high-voltage high-power magnetrons. In this paper, a multi-mode high voltage DC-DC converter with a wide output voltage range is proposed, which is composed of two input series connected full-bridge inverters, six inductor – inductor – capacitor (LLC) resonant networks, and two types of voltage multipliers. The proposed high voltage power supply owns six operation modes and five available output voltage ranges by modifying the inverter's driving scheme. Thus, the proposed converter can reduce the variation range of the resonant network's gain when regulating the output voltage widely. In this paper, a detailed comparative analysis is presented of the operating principle of the proposed topology and its six operation modes. Moreover, the expression of its output voltage gain is shown with the control strategy. Finally, a 7.5kW 3.5-10kV output prototype is built to verify. The results convincingly demonstrate the applicability of the proposed converter offering high efficiency over a wide range of output power.
22 April 2025 in IEEE Transactions on Power Electronics
High voltage power supplies with voltage multipliers (VMs) show high feasibility due to their low voltage stress on the components. But as for the traditional VMs, the more stages, the higher output voltage drop (OVD) and higher output voltage ripple (OVR) when using the same number of capacitors, then high-voltage components and wide regulation range for the inverter may be required to achieve a stable output voltage. This article proposes a high voltage power supply with a hybrid full-wave VM (HFWVM), which is derived from several full-wave Dickson VM sets connected in Cockcroft-Walton way (series stacked). It features lower OVR, lower OVD, and faster start-up time compared with other VMs under the same voltage stress level on the components, especially in high-voltage output applications. In this article, the detailed derivation process and analysis of the proposed HFWVM are presented. The OVD and OVR are derived along with the operational mode. Comparison with other VMs is also carried and it demonstrates the advantages of the proposed HFWVM in OVR and OVD. Finally, a 2.8-kW/15-kV output prototype is built, and the results convincingly demonstrate the applicability and the analysis of the high voltage power supply and the advantage of the HFWVM.
28 November 2023 in IEEE Transactions on Industrial Electronics
Pulsed power loads (PPLs) have the requirements of fast dynamic and high-power ratings, which may cause periodic power oscillations in traditional dc microgrid systems. Therefore, an improved dual natural switching surface (DNSS) boundary control law is proposed for multilevel noninverting buck-boost converter to dynamically synchronize the periodic power of PPLs within the minimum switching cycle by deriving and tracking the controlled trajectories. First, the variable structure model is established to derive the natural switching surfaces. Then, a graphical characteristic analysis of the transient switching trajectory is presented for the derivation of DNSSs, which can be divided into the primary and the secondary switching. Also, the control strategy based on DNSS is proposed. Due to the super dynamic performance of boundary control and the load characteristic of PPLs, the inductor current may be over the maximum permissible current, and online over-current protection is designed to achieve fast dynamic performance by limiting the inductor current. Finally, simulations and experiments are given to verify the proposed control law. The results show the proposed method has great dynamic performance for PPLs.
26 June 2023 in IEEE Transactions on Industrial Electronics
Two or more high-voltage isolated power supplies are required for many high voltage applications, such as in microwave generating and ion implantation. Traditionally, several separate high-voltage isolated converters are employed, which contain many components and complex control systems. This paper proposes a dual-output converter, which consists of two input series connected full-bridge inverters, two LCC and two LLC resonant networks connected with the full-wave Cockcroft–Walton voltage multipliers and the synchronous rectifiers, respectively. Comparing with the traditional solutions, the number of switches and their peripheral circuits are reduced. By regulating the switching frequency and three phase shift angles of the inverter, the proposed converter allows one port to operate alone or both ports to operate simultaneously, while achieving soft switching, and maintaining the voltage balancing between two input series capacitors. In this paper, a detailed analysis of the operating principle and its characteristics such as the output voltage gain and soft switching are presented. Finally, a prototype with two outputs, 4kV-5kV/3.8kW and 15V/600W, is built to verify. The results convincingly demonstrate the applicability of offering one or two isolated outputs, which offers a high integrated, efficient and simple solution for powering the magnetrons.