Árpád Czifra

Prof. Dr. Árpád Czifra

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
RHRichárd Horváth
Richárd Horváth
Árpád CzifraÁrpád Czifra
Árpád Czifra
ÁDÁgota Drégelyi-Kiss
Ágota Drégelyi-Kiss

14 July 2020 in Frontiers in Mechanical Engineering
Verified
Journal Article
Open access
PDF file
Árpád CzifraÁrpád Czifra
Árpád Czifra
IBIstván Barányi
István Barányi
The reliable characterization of surface topographies—especially in case of tribological processes—requires complex and comprehensive solution methods. The use of a combination of roughness parameters offers effective solutions in many cases. In our study, we found a close correlation between the Sdq-Sdr parameter pair and we applied the two parameters as a topological map. Surface topographies resulting from different machining techniques (turned, milled, ground, honed, electric discharge machined, and sintered) were placed in the topological map and their possibilities of use were explored. It was established that surfaces with an orientation characteristically have lower Sdq-Sdr value pairs than non-oriented or multi-oriented surfaces; however, surface defects, injuries and machining discrepancies increase the values of Sdq-Sdr parameters. Then the Sdq-Sdr topological map was applied for worn surfaces resulting from abrasive and tribochemical processes, and it was established that the worn surfaces examined are characterized by small Sdq-Sdr values. Test results showed that in case of manufacturing processes, the topological map is suitable for identifying manufacturing discrepancies and manufacturing defects, and it highlights structural changes in the microgeometry in the course of the wear process.

1 January 2022 in Tribology and Materials
Verified
Journal Article
Open access
AVAleksandar Vencl
Aleksandar Vencl
Blaza StojanovićBlaza Stojanović
Blaza Stojanović
Ranka SudžumRanka Sudžum
Ranka Sudžum
Simon KlancnikSimon Klancnik
Simon Klancnik
Árpád CzifraÁrpád Czifra
Árpád Czifra
Marta HarničárováMarta Harničárová
Marta Harničárová
The objective of this work was to investigate the influence of the addition of a small amount of SiC nanoparticles on the mechanical characteristics and wear resistance of ZA-27 alloy. The ZA-27 alloy-based nanocomposites were produced by a relatively cheap compocasting process preceded by mechanical alloying. Reinforcing elements were the silicon carbide (SiC) nanoparticles with an average size lower than 50 nm and in very small amounts of 0.2, 0.3 and 0.5 wt. %. Wear tests were realized on a block-on-disc tribometer under lubricated sliding conditions, at two sliding speeds (0.25 and 1 m/s), two normal loads (40 and 100 N) and a sliding distance of 1000 m. Optimisation of the SiC amount was performed by applying the Taguchi method, showing that the SiC amount of 0.5 wt. % is optimal for the given testing conditions. Prediction of the results and wear maps were also conducted. The analysis of variance showed that the SiC amount has the greatest influence on wear rate (70.8 %), followed by the normal load (19.8 %), and the sliding speed (3.9 %), while the influences of all interactions between these factors did not have any significant influence.

1 June 2011 in Measurement
Verified
Journal Article
Closed access
Árpád CzifraÁrpád Czifra
Árpád Czifra
TGT. Goda
T. Goda
EGE. Garbayo
E. Garbayo

30 April 2008 in Meccanica
Verified
Journal Article
Closed access
PDF file
Árpád CzifraÁrpád Czifra
Árpád Czifra
KVK. Váradi
K. Váradi
SHS. Horváth
S. Horváth

20 January 2011 in Meccanica
Verified
Journal Article
Closed access
PDF file
Árpád CzifraÁrpád Czifra
Árpád Czifra
SHSándor Horváth
Sándor Horváth