Sylvia Hagedorn

Dr. Sylvia Hagedorn

Ferdinand-Braun-Institut (FBH), Leibniz-Institut für Höchstfrequenztechnik, Gustav-Kirchhoff-Str. 4, 12489 Berlin, Germany

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 February 2020 in Physica Status Solidi (a)
Verified
Journal Article
Open access
PDF file
SHSylvia Hagedorn
Sylvia Hagedorn
SWSebastian Walde
Sebastian Walde
AKArne Knauer
Arne Knauer
NSNorman Susilo
Norman Susilo
DPDaniel Pacak
Daniel Pacak
MWMarkus Weyers
Markus Weyers
Herein, the scope is to provide an overview on the current status of AlN/sapphire templates for ultraviolet B (UVB) and ultraviolet C (UVC) light‐emitting diodes (LEDs) with focus on the work done previously. Furthermore, approaches to improve the properties of such AlN/sapphire templates by the combination of high‐temperature annealing (HTA) and patterned AlN/sapphire interfaces are discussed. While the beneficial effect of HTA is demonstrated for UVC LEDs, the growth of relaxed AlGaN buffer layers on HTA AlN is a challenge. To achieve relaxed AlGaN with a low dislocation density, the applicability of HTA for AlGaN is investigated.

8 May 2023 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
TKTim Kolbe
Tim Kolbe
AKArne Knauer
Arne Knauer
JRJens Rass
Jens Rass
HCHyun Kyong Cho
Hyun Kyong Cho
SHSylvia Hagedorn
Sylvia Hagedorn
MWMarkus Weyers
Markus Weyers
Far-ultraviolet-C (far-UVC) light-emitting diodes (LEDs) with an emission wavelength of 234 nm with different polarization-doped AlGaN hole injection layers (HILs) are compared regarding their emission power, voltage, and leakage current. The influence of the thickness of the polarization-doped layer (PDL), an additional Mg doping of the PDL, as well as a combination of a PDL with a conventionally Mg-doped AlGaN HIL will be discussed. The different PDL thicknesses show nearly no influence on the emission power or voltage. However, the leakage current of the LEDs below the turn-on voltage decreases with an increasing thickness of the PDL. In contrast, an additional Mg doping of the PDL ([Mg] ∼ 1.5 × 1019 cm−3) results in a fivefold decrease in the emission power at an unchanged voltage and leakage current. Finally, a combination of a PDL and a conventionally Mg-doped AlGaN layer ([Mg] ∼ 1.5 × 1019 cm−3) as a HIL shows also a similar emission power and voltage compared to the single PDL, but the leakage current increases. Based on these optimizations, 234 nm LEDs were realized with a maximum external quantum efficiency of 1% at 20 mA, an emission power of 4.7 mW, and a voltage of 9.0 V at 100 mA. This shows that the polarization doping concept is well suited to realize far-UVC LEDs with improved performance compared to LEDs with a conventionally Mg-doped p-side.

1 August 2016 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
SHSylvia Hagedorn
Sylvia Hagedorn
AKArne Knauer
Arne Knauer
AMAnna Mogilatenko
Anna Mogilatenko
EREberhard Richter
Eberhard Richter
MWMarkus Weyers
Markus Weyers

2 January 2023 in Applied Physics Letters
Verified
Journal Article
Open access
PDF file
AKA. Knauer
A. Knauer
TKTim Kolbe
Tim Kolbe
SHSylvia Hagedorn
Sylvia Hagedorn
JHJ. Hoepfner
J. Hoepfner
MGMartin Guttmann
Martin Guttmann
MWM. Weyers
M. Weyers
High temperature annealed AlN/sapphire templates exhibit a reduced in-plane lattice constant compared to conventional non-annealed AlN/sapphire grown by metalorganic vapor phase epitaxy (MOVPE). This leads to additional lattice mismatch between the template and the AlGaN-based ultraviolet-C light emitting diode (UVC LED) heterostructure grown on these templates. This mismatch introduces additional compressive strain in AlGaN quantum wells resulting in enhanced transverse electric polarization of the quantum well emission at wavelengths below 235 nm compared to layer structures deposited on conventional MOVPE-grown AlN templates, which exhibit mainly transverse magnetic polarized emission. In addition, high temperature annealed AlN/sapphire templates also feature reduced defect densities leading to reduced non-radiative recombination. Based on these two factors, i.e., better outcoupling efficiency of the transverse electric polarized light and an enhanced internal quantum efficiency, the performance characteristic of far-UVC LEDs emitting at 231 nm was further improved with a cw optical output power of 3.5 mW at 150 mA.

22 November 2021 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
LCLeonardo Cancellara
Leonardo Cancellara
TMToni Markurt
Toni Markurt
TSTobias Schulz
Tobias Schulz
MAMartin Albrecht
Martin Albrecht
SHSylvia Hagedorn
Sylvia Hagedorn
ZSZlatko Sitar
Zlatko Sitar
Recovery of epitaxial AlN films on sapphire at high temperatures is now an established process to produce pseudo-substrates with high crystalline perfection, which can be used to grow epitaxial structures for UV-light-emitting devices. To elucidate the elementary mechanisms taking place during the thermal treatment of MOVPE-grown films, we studied as-grown and annealed samples combining transmission electron microscopy techniques and secondary ion mass spectrometry (SIMS). By using SIMS, we find a temperature-dependent increase in the overall oxygen content of the films, which cannot be explained quantitatively with either simple bulk or pure pipe-diffusion from the sapphire substrate. Instead, we propose a lateral outdiffusion from the dislocation cores to explain qualitatively and quantitatively the presence of observed oxygen concentration plateaus. Based on the formation enthalpy of various atomic defects and complexes found in literature, we conclude that the di-oxygen/aluminum vacancy complex (VAl–2ON) is the dominant point defect controlling the annealing process. The formation of this defect at high temperatures promotes a dislocation core climb process, which causes the annihilation/fusion of the threading dislocation segments.

8 July 2021 in Physica Status Solidi (b)
Verified
Journal Article
Open access
PDF file
SHSylvia Hagedorn
Sylvia Hagedorn
AMAnna Mogilatenko
Anna Mogilatenko
SWSebastian Walde
Sebastian Walde
DPDaniel Pacak
Daniel Pacak
JWJonas Weinrich
Jonas Weinrich
MWMarkus Weyers
Markus Weyers
Using the example of epitaxial lateral overgrowth of AlN on trench‐patterned AlN/sapphire templates, the impact of introducing a high‐temperature annealing step into the process chain is investigated. Covering the open surfaces of sapphire trench sidewalls with a thin layer of AlN is found to be necessary to preserve the trench shape during annealing. Both the influence of annealing temperature and annealing duration are investigated. To avoid the deformation of the AlN/sapphire interface during annealing, the annealing duration or annealing temperature must be low enough. Annealing for 1 h at 1730 °C is found to allow for the lowest threading dislocation density of 3.5 × 108 cm−2 in the subsequently grown AlN, while maintaining an uncracked smooth surface over the entire 2 in. wafer. Transmission electron microscopy study confirms the defect reduction by high‐temperature annealing and reveals an additional strain relaxation mechanism by accumulation of horizontal dislocation lines at the interface between annealed and nonannealed AlN. By applying a second annealing step, the dislocation density can be further reduced to 2.5 × 108 cm−2.