In this paper, mode conversion occurring in differential lines with cross section affected by geometric imbalance is investigated by recognizing a strict analogy with crosstalk, and by rephrasing in the modal domain the assumption of weak coupling (usually exploited for crosstalk analysis) in terms of weak imbalance. The derivation focuses on the conversion of the differential mode signal into common mode (CM) noise responsible for undesired radiated emissions, and leads to an approximate circuit model for CM-current prediction, in which the effects due to mode conversion are included by distributed voltage and current sources. Model accuracy is assessed by experimental and numerical validations involving unbalanced microstrip lines.

In this paper, the effects of undesired asymmetry and nonuniformity on differential line (DL) circuits are modeled as deviations from the ideal, nominal geometrical characteristics of a perfectly symmetrical and uniform DL, whose performance is taken as reference. To this end, the involved multiconductor transmission line equations are solved in the modal domain by a decoupled approach based on the perturbation of the p.u.l. parameters of the ideal DL on one hand, and on the assumption of weak coupling between the corresponding differential and common mode equivalent circuits on the other. Three illustrative DL structures are considered and analytically solved, with the objective to put in evidence the effects of the aforesaid geometrical nonidealities on the degradation of the differential mode signal propagating along the DL as well as on the generation of undesired common mode currents/voltages. A circuit interpretation of the involved phenomena is provided, and the relevant geometrical parameters are identified.

This work investigates the performance of RF immunity procedures exploiting semi-rigid coaxial test probes as coupling devices to inject continuous wave (CW) RF power into the outlets of Integrated Circuits (ICs). Two solutions are presented, both offering the advantage with respect to the traditional direct power injection method, to run the test without removing the IC from its actual PCB. The first procedure resorts to near-field coupling to inject the noise into an interconnecting trace. The second procedure requires metallic contact between the probe tip and the injection point (e.g., a via or an IC pin). Specific figures of merit, such as coupling and power efficiency, test repeatability and intrusiveness, sensitivity to setup parameters and lateral spatial resolution, are introduced and used to ascertain the effectiveness of the proposed procedures. To this end, both numerical simulations and measurements were carried out on several PCBs. Feasibility of the proposed immunity procedures is eventually proven by an application example, involving a thermal sensor as device under test.

Electromagnetic interference (EMI) from renewable power systems to the grid attracts more attention especially in the low-frequency range, due to the low switching frequency of high-power inverters. It is significantly important to derive EMI models of power inverters as well as to develop strategies to suppress the related conducted emissions. In this work, black-box modelling is applied to a three-phase inverter system, by implementing an alternative procedure to identify the parameters describing the active part of the model. Besides, two limitations of black-box modelling are investigated. The first regards the need for the system to satisfy the linear and time-invariant (LTI) assumption. The influence of this assumption on prediction accuracy is analysed with reference to the zero, positive and negative sequence decomposition. It is showing that predictions for the positive/negative sequence are highly influenced by this assumption, unlike those for the zero sequence. The second limitation is related to the possible variation of the mains impedance which is not satisfactorily stabilized at a low frequency outside the operating frequency range of standard line impedance stabilization networks.

Random Pulse Width Modulation (RPWM) allows controlling the switching signal of power converters in order to reduce the harmonic peaks by spreading the noise spectrum. Currently, many manufacturers of power converters are deploying this modulation scheme in order to comply with Electromagnetic Compatibility (EMC) test requirements. However, when the converters coexist with Power Line Communication (PLC) systems, such as in Smart Grid (SG) applications, resorting to RPWM needs further investigations since it potentially affects the communication channel by increasing the bit error rate. This possible detrimental effect is investigated in this work, by considering a PLC system for automatic meter reading (AMR) implemented in a SG application. To this end, the model of a complete PLC system is implemented in SIMULINK, and Quadrature Phase Shift Keying (QPSK) modulation is used to model the PLC modems in the communication channel. Results show that, even if the deployment of RPWM techniques may lead to an appreciable reduction/spreading of the peaks in the noise spectrum, it may also lead to an increase of the bit error rate on the PLC system.

Undesired conversion between common-mode (CM) and differential-mode (DM) noise often occurs in modern electronic and electrical systems, posing challenges in terms of Electromagnetic Compatibility (EMC). Modal analysis represents a crucial tool in EMC investigation and provides insight into the mechanism underlying mode conversion. By inspecting CM and DM behaviors and their interconversion, it allows for understanding of conducted emission propagation mechanisms, drives electromagnetic interference (EMI) filter design towards optimal/tailored solutions, and enables the possibility to identify the main contributors to the radiated emission phenomenon. This paper offers a comprehensive review of mathematical methodologies and modelling strategies for EMC-oriented modal analysis, with particular emphasis on mode conversion phenomena. To this end, modal decomposition techniques and standard parameters for quantifying mode conversion are summarized and compared. Additionally, the paper provides an overview and in-depth discussion of different scenarios and test cases in which mode conversion occurs, with the final goal to achieve a systematic comprehension of its root causes and consequences within power and communication systems. Eventually, a survey of circuit modelling approaches for mode conversion is presented, offering insights into addressing this phenomenon effectively.