Currently, silicon and silicon-based composite materials are widely used in microelectronics and solar energy devices. At the same time, silicon in the form of nanoscale fibers and various particles morphology is required for lithium-ion batteries with increased capacity. In this work, we studied the electrolytic production of nanosized silicon from low-fluoride KCl–K2SiF6 and KCl–K2SiF6–SiO2 melts. The effect of SiO2 addition on the morphology and composition of electrolytic silicon deposits was studied under the conditions of potentiostatic electrolysis (cathode overvoltage of 0.1, 0.15, and 0.25 V vs. the potential of a quasi-reference electrode). The obtained silicon deposits were separated from the electrolyte residues, analyzed by scanning electron microscopy and spectral analysis, and then used to fabricate a composite Si/C anode for a lithium-ion battery. The energy characteristics of the manufactured anode half-cells were measured by the galvanostatic cycling method. Cycling revealed better capacity retention and higher coulombic efficiency of the Si/C composite based on silicon synthesized from KCl–K2SiF6–SiO2 melt. After 15 cycles at 200 mA·g−1, material obtained at 0.15 V overvoltage demonstrates capacity of 850 mAh·g−1.
The possibility of silicon electrodeposition from the low-melting LiCl-KCl-CsCl-K2SiF6 electrolytes has been studied. The stability of a silicon-containing additive was studied by cyclic voltammetry, and the rate constant of the chemical reaction of SiF4 release at a temperature of 827 K was calculated. It is determined that the constants of velocity values in the melt based on eutectic composition are 2 orders of magnitude higher, which indicates a higher rate of formation of volatile compounds. Cyclic voltammetry was also used to study the electrochemical behavior of K2SiF6 in the melts under study. It was found that the silicon electroreduction at the cathode is not reversible and proceeds in one 4-electron reaction. The diffusion coefficient calculated by the Matsuda-Ayabe equation was 0.72·10−5 cm2·s−1 at temperature of 823 K. According to the obtained voltammograms, the parameters for the silicon electrodeposition were selected. At a potential of −0.4 V vs QRE, dendritic silicon deposits were obtained.
1
1 February 2022 in Journal of the Electrochemical Society
In this paper we report characteristics and electrochemical properties of silicon fibers used as lithium-ion battery anode. All samples were synthesized by potentiostatic electrodeposition from molten KCl–K2SiF6. From molten KCl–CsCl–K2SiF6 deposition was carried out in galvanostatic mode. Despite the synthesis in inert atmosphere and absence of oxygen containing compounds in the melt resulting silicon after washing contains at least 15 at% oxygen. Silicon fibers synthesized at −250 mV (vs Si) were the thinnest with diameter as small as 100 nm; average fiber length increased with increasing overvoltage. Addition of CsCl to the melt results in decrease of the average fibers diameter. Silicon fibers synthesized at −250 mV (vs Si) in KCl–K2SiF6 melt showed the best cycling performance with capacity of 1030 mAh·g−1 at 0.2 A·g−1 discharge current and capacity of 715 mAh·g−1 after 10 cycles. Lithium diffusion coefficients calculated from galvanostatic intermittent titration technique (GITT) are common for silicon-based anode. The highest initial diffusion coefficient value of 6.68·10−11 cm2·s−1 was achieved for silicon synthesized from melt with addition of CsCl. Low capacity and rapid capacity fading for all samples can be caused by high silicon dioxide content, further treatment of synthesized silicon is necessary to achieve higher performance.
The methods of electrolytic production of silicon and materials based on it with controlled morphology, particle size, and trace element content are important for the development of new microelectronic and renewable energy devices. In this work, the possibility of silicon production by the electrolysis of the KCl–K2SiF6 chloride melt with a low content of fluorine ions using quartz (silicon oxide) as a starting material is studied. Cyclic chronovoltammetry is used to determine the silicon electrodeposition parameters (cathode current density) and the recommended SiO2 content in the melt, which allows stable electrolysis without electrode passivation. A series of experiments on silicon electrodeposition from the melt using a graphite anode and a graphite cathode is performed at various cathode current densities (10–50 mA/cm2). Silicon deposits are formed, and their composition and morphology are studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. Predominant silicon deposition in the form of fibers with an average diameter of 0.3–0.8 μm and larger particles of an arbitrary shape is observed. As the cathode current density increases, the amount of β quartz in the deposit is found to increase, and its appearance is likely to be caused by the codeposition of potassium in the form of silicides and their subsequent hydrolysis during the separation of salts from the deposit in distilled water. The measurement results are used to propose a method for continuous electrolytic silicon production from quartz; it includes periodic removal of the cathode with a deposit from an electrolysis cell and loading quartz into the melt.
The unique properties of zirconium silicides attract the attention of a large number of authors from various scientific fields. Expansion of application methods also poses the challenge of developing new, more environmentally friendly and affordable methods of production. The most environmentally friendly method without equipment requirements is the electrolysis of the molten salt. The work proposes a method for producing zirconium silicides by electrolysis of the KCl–K2SiF6–ZrO2 melt. In order to substantiate the electrolysis parameters, the kinetics of cathodic reduction was studied and the limiting stage of the process was determined. The structure and phase composition of the cathode deposit were studied using X-ray diffraction and electron scanning microscopy. In the course of the work, conclusions were drawn about the change in the content of the ZrO2 additives on the morphology of the sediment, and it was also suggested that it was possible to obtain zirconium silicides from more accessible raw materials, such as zircon.