Currently, silicon and silicon-based composite materials are widely used in microelectronics and solar energy devices. At the same time, silicon in the form of nanoscale fibers and various particles morphology is required for lithium-ion batteries with increased capacity. In this work, we studied the electrolytic production of nanosized silicon from low-fluoride KCl–K2SiF6 and KCl–K2SiF6–SiO2 melts. The effect of SiO2 addition on the morphology and composition of electrolytic silicon deposits was studied under the conditions of potentiostatic electrolysis (cathode overvoltage of 0.1, 0.15, and 0.25 V vs. the potential of a quasi-reference electrode). The obtained silicon deposits were separated from the electrolyte residues, analyzed by scanning electron microscopy and spectral analysis, and then used to fabricate a composite Si/C anode for a lithium-ion battery. The energy characteristics of the manufactured anode half-cells were measured by the galvanostatic cycling method. Cycling revealed better capacity retention and higher coulombic efficiency of the Si/C composite based on silicon synthesized from KCl–K2SiF6–SiO2 melt. After 15 cycles at 200 mA·g−1, material obtained at 0.15 V overvoltage demonstrates capacity of 850 mAh·g−1.
1
1 May 2021 in International Journal of Hydrogen Energy
Nowadays, research aimed at the development of materials with increased energy density for lithium-ion batteries are carried out all over the world. Composite anode materials based on Si and C ultrafine particles are considered promising due to their high capacity. In this work, a new approach for carbothermal synthesis of C/SiC composite mixtures with SiC particles of fibrous morphology with a fiber diameter of 0.1–2.0 μm is proposed. The synthesis was carried out on natural raw materials (quartz and graphite) without the use of complex equipment and an argon atmosphere. Using the proposed method, C/SiC mixture as well as pure SiC were synthesized and used to manufacture anode half-cells of lithium-ion batteries. The potential use of the resulting mixtures as anode material for lithium-ion battery was shown. Energy characteristics of the mixtures were determined. After 100 cycles, pure SiC reached a discharge capacity of 180 and 138 mAh g−1 at a current of C/20 and C, respectively, and for the mixtures of (wt%) 29.5C–70.5 SiC and 50Si–14.5C–35.5SiC discharge capacity of 328 and 400 mAh g−1 at a current of C/2 were achieved. The Coulombic efficiency of the samples during cycling was over 99%.
Proton conducting materials are used in electrochemical devices such as proton conducting fuel cells and proton conducting electrolyzers. These devices belong to the hydrogen energy field and serve the goals of clean energy and sustainable environmental development. Layered perovskites are a promising class of proton conducting electrolytes. Cationic co-doping is a well-known method to improve the transport properties of classical perovskite ABO3. However, data on the application of this method to layered perovskites are limited. In this work, the bilayered perovskites BaLa1.9−xSrxGd0.1In2O7−0.5x have been prepared and studied for the first time. The possibility of oxygen-ionic and proton transport was demonstrated. Cationic co-doping was shown to increase the proton conductivity values by up to 1.5 orders of magnitude.
Compositions of ultrafine Si and C particles are promising anode materials for lithium-ion power sources with improved energy characteristics. In the work, samples of lithium-ion power sources with an anode made of ultrafine SiC fibers, as well as mixtures of SiC fibers with graphite (C/SiC) and electrolytically deposited submicron silicon fibers (C/Si/SiC) were fabricated and studied for energy characteristics. The working ability of the mixtures obtained during lithiation/delithiation was shown, and the main energy characteristics of the investigated anode half-cells were determined. After 100 cycles, the SiC anode reached a discharge capacity of 180 and 138 mA·h/g at a charge current of C/20 and C, respectively. Anodes made of mixtures (wt%) 29.5C-70.5SiC and 50Si-14.5C-35.5SiC show discharge capacities of 328 and 400 mA·h/g at a charge current of C/2. The Coulomb efficiency of all samples was above 99%.
Представлены результаты исследования плосколистовых ультрафильтрационных мембран, полученных инверсией фаз (отливкой на стеклянной подложке) с использованием растворов 13–16 мас% поливинилхлорида в N,N-диметилацетамиде. Показана зависимость структуры, морфологии и эксплуатационных свойств мембран от концентрации отливочных растворов поливинилхлорида. Установлено, что увеличение концентрации поливинилхлорида в отливочном (формовочном) растворе с 14 до 16 мас% приводит к уменьшению проницаемости мембран на 57.7% для дистиллированной воды и в среднем на 68.9% для проб сточной воды исследованных автомоек. Более стабильные результаты очистки проб сточных вод автомоек от основных загрязнителей получены при фильтровании через мембрану, полученную из раствора поливинилхлорида концентрацией 14%.