A Hybrid Fault Current Limiter (HFCL) is a device that combines the properties of both Superconducting Fault Current Limiter (SFCL) and Solid-State Fault Current Limiter (SSFCL). This combination aims to provide the fast response time typically associated with SFCLs and simultaneously provide the capacity to withstand longer limitation time and reliable application under high voltages, as found in SSFCLs. In this context, an HFCL prototype was tested to analyze its performance and compare its characteristics with those of the SFCL and the SSFCL modules separately. This work aims to demonstrate that the HFCL presents a high level of protection, besides being more compact and cost-effective compared to SFCLs, since the proposed hybrid device can be designed using less HTS material than common resistive SFCL. Experimental tests were made to analyze the current limitation capacity for the three FCLs. The results showed that the HFCL could reduce the fault current with a reliable fault detection system.
The development of X-ray-absorbing scintillating nanoparticles is of high interest for solving the short penetration depth problem of visible and infrared light in photodynamic therapy (PDT). Thus, these nanoparticles are considered a promising treatment for several types of cancer. Herein, gadolinium oxide nanoparticles doped with europium ions (Gd2O3:Eu3+) were obtained by using polyvinyl alcohol as a capping agent. Hybrid silica nanoparticles decorated with europium-doped gadolinium oxide (SiO2-Gd2O3:Eu3+) were also prepared through the impregnation method. The synthesized nanoparticles were structurally characterized and tested to analyze their biocompatibility. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy confirmed the high crystallinity and purity of the Gd2O3:Eu3+ particles and the homogeneous distribution of nanostructured rare earth oxides throughout the fumed silica matrix for SiO2-Gd2O3:Eu3+. Both nanoparticles displayed stable negative ζ-potentials. The photoluminescence properties of the materials were obtained using a Xe lamp as an excitation source, and they exhibited characteristic Eu3+ bands, including at 610 nm, which is the most intense transition band of this ion. Cytotoxicity studies on mouse glioblastoma GL261 cells indicated that these materials appear to be nontoxic from 10 to 500 μg·mL−1 and show a small reduction in viability in non-tumor cell lines. All these findings demonstrate their possible use as alternative materials in PDT.
Thin films usually grow when doing deposition in vacuum using Pulsed Laser Deposition (PLD). However, when depositing silver (Ag) on silicon (Si) substrates using PLD in a vacuum, it consistently leads to the formation of nanoparticles (NPs) [ 1, 2]. In this study, we performed a systematic investigation of the effect of argon (Ar) gas pressure and substrate surface free energy on the formation of the Ag NPs prepared via PLD. The results show that the Ag NPs can form when the deposition is performed either in vacuum or in Ar with pressure higher than 10-2 Torr on Si substrate. At an intermediate Ar pressure of 10-4 Torr, a thin film can form due to lower energy of the Ag atoms upon reaching the substrate surface, as shown in Figure 1. Adding a buffer layer with a similar surface energy to that of Ag (such as a Ni layer) can also result a thin film formation. Additionally, it was observed that the deposition rate of Ag nanoparticles prepared in a vacuum does not correlate with the deposition time. To understand this phenomenon, another Si substrate was placed adjacent to the target to assess whether Ag atoms were rebounding from the substrate as schematized in Figure 2. As a result, a smooth Ag thin film formed on the second substrate (Figure 3b), while the first substrate continued to display only silver nanoparticles (Figure 3a). In conclusion, the formation of Ag NPs in vacuum prepared by PLD is due to a balance of the PLD deposition rate and a sputtering process of the silver deposited by high energetic Ag atoms from the plume [ 3] in addition to a very different surface free energy of the substrate and the deposited material. Adding Ar gas can decrease the energy of the Ag atoms and thus thin films can be formed. Further increase of the Ar pressure induces more collision between Ag and Ar atoms. As a result, Ag NPs can be formed before they arrive at the substrate [ 4].