Ji jiajia

Dr. Ji jiajia


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2022 in Energies
Verified
Journal Article
Open access
PDF file
JJJi jiajia
Ji jiajia
JHJun Hu
Jun Hu
SMShuai Ma
Shuai Ma
RXRong Xu
Rong Xu
The onset of rotating stall and surge in compressors limits the operating range of aero-engines. Accurately predicting the key features during these events is critical in the engine design process. In this paper, a three-dimensional computational model for transient simulation of multi-stage axial compressors during stall is proposed. The kinetic equations describing the dynamic process of the compression system are constructed, with a 3D through-flow model for the compression part and a 1D gas collector model for the outlet part. The calculation of the source term is performed using the developed body-force model, which realizes the correlation between the deviation angle and the loss coefficient with the inlet parameters in various flow regions. Validated on a single-stage compressor and a single-rotor fan, the results show that the method is capable of capturing the stall and surge features correctly and that the three-dimensional structure of the stall cell can be captured. In addition, this model could be used for the analysis of the surge load, which is significant for the structural integrity of the compressor.

2 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
RXRong Xu
Rong Xu
JHJun Hu
Jun Hu
XWXuegao Wang
Xuegao Wang
CJChao Jiang
Chao Jiang
JJJi jiajia
Ji jiajia
In this paper, an experimental study was carried out on the rotating instability in an axial compressor subjected to inlet steady paired swirl distortion. In order to deepen the understanding of the rotating stall mechanism under inlet steady paired swirl distortion, the dynamic-wall static pressure near the rotor tip was monitored to characterize the flow in the rotor tip region at different circumferential stations. In the experiment, the dynamic characteristics of the rotor tip flow field at a stable operating point and during the process from the stable point to complete stall were measured. The results indicated that for the compressor with a 2 mm rotor tip clearance, the inlet paired swirl distortion induced rotating instability (RI) near the stall point, causing the compressor to enter stall in advance. Compared with the RI intensity of the clean inlet, the distortion with a swirling blade stagger angle (αst) of ±20° increased the RI intensity up to 69.8%, while for αst equal to ±40°, the RI intensity increased at most by 135.8%. As the rotor tip clearance increased to 3 mm, the co-rotating swirl in the paired swirl distortion inhibited the appearance of RI, while the counter-rotating part aggravated the development of RI. At the beginning, the process of the compressor rotating stall involved the alternation of short-scale disturbance and long-scale disturbance. The co-rotating swirl weakened the perturbation propagated from the counter-rotating swirl sector. Once the inhibition was no longer present, the short-scale disturbance rapidly developed into a long-scale disturbance and then entered the rotating stall.

1 January 2025 in Physics of Fluids
Verified
Journal Article
Open access
YLYuqi Lu
Yuqi Lu
ZWZhiqiang Wang
Zhiqiang Wang
JJJi jiajia
Ji jiajia
In this paper, an unsteady Reynolds-averaged N–S equations (URANS) method is developed to calculate the surge dynamic process of compressor. Using this method, the surge dynamic process of a four-stage high-speed axial compressor at 70% design speed under different B parameters is numerically simulated. The simulation results show that the classical surge is induced when the B parameter is 0.35 and 0.4, and the deep surge is induced when the B parameter is 1.0 and 1.44. The surge frequency decreases with the increase in the B parameter, and the surge frequency obtained when the B parameter is 1.44 is very close to the experimental results. The body-force model (BFM) is another numerical simulation method with low computational cost and can capture the details of the flow field to a certain extent. For the same high-speed four-stage compressor, under the condition that the surge frequency is almost the same as that in the experiment, the calculation results of the surge dynamic process by the URANS method and the previously developed BFM are compared. The results show that the prediction of the dynamic pressure of the wall by the two methods is in good agreement with the experimental data, and the two methods have also achieved similar results in the prediction of the blade force. The meaningful comparison results show that the URANS method can be used as a supplement to the experiment in many aspects and provide more abundant calibration data for the further development of BFM.

7 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
SMShuai Ma
Shuai Ma
JHJun Hu
Jun Hu
XWXuegao Wang
Xuegao Wang
JJJi jiajia
Ji jiajia
It is well known that variations in stagger angle between rotor blades affect compressor performance. In this paper, the stagger angle of blade No. 8 is increased or decreased by six degrees for non-uniformity, and the influence of rotor non-uniformity caused by the change in only one blade stagger angle on the performance and stability of the compressor is investigated. The experimental results show that whether the local rotor stagger angle increases or decreases, the compressor stability will deteriorate. If the stagger angle of blade No. 8 is reduced by six degrees, the flow coefficient at the stall point increases by 8.5%. If the stagger angle of blade No. 8 is increased by six degrees, the flow coefficient at the stall point increases by 1.5%. The reason for the deterioration of compressor stability caused by the local non-uniform rotor stagger angle is explored. When the stagger angle of rotor blade No. 8 deviates from the designed state, the load of blade No. 8 and the surrounding blades will change. The load on rotor blade No. 8 increases when the stagger angle decreases. In the near-stall condition, blade No. 8 becomes the “dangerous blade” that triggers the stall. As the stagger angle of rotor blade No. 8 increases, the load on blade No. 8 decreases. However, the load on blade No. 9 increases due to flow redistribution and blade No. 9 becomes a “dangerous blade” that triggers stall. The “dangerous blade” caused by the non-uniformity of stagger angle is the direct reason for the advance of the compressor rotating stall.

1 May 2024 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
JJJi jiajia
Ji jiajia
RCRonghui Cheng
Ronghui Cheng
JHJun Hu
Jun Hu
ZWZhiqiang Wang
Zhiqiang Wang
SMShuai Ma
Shuai Ma
In this paper, a method for simulating the instability transient process of the axial compression system based on the body-force model is developed, and a corresponding simulation program is developed. Simulations of the transient process of instability were carried out on a high-speed four-stage compressor and compared with experimental data. At 50% of the design rotational speed, the type of instability was rotating stall, and the simulated and experimental stall cell propagation speed were very close to each other. At 70% of the design rotational speed, the type of instability was surge. A “surge loop” was simulated, and the surge period and the percentage of time spent in each phase were consistent with the experiments. The simulation successfully predicted the blockage in the surge re-pressurization phase, proving the reliability of the simulation results. In addition, the computation yields more information about the flow field. By summing the blade forces of all grids on a blade row by volume, the surge loadings are obtained. The analysis of the axial momentum equation shows that the obtained blade force variations are reasonable. The simulation time of the multistage axial compressor is greatly reduced compared to the full annulus three-dimensional unsteady Reynolds-averaged Navier–Stokes method, demonstrating its great advantage in the design phase of the compressor.

8 December 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
SMShuai Ma
Shuai Ma
JHJun Hu
Jun Hu
XWXuegao Wang
Xuegao Wang
JJJi jiajia
Ji jiajia
To make measurement of end-wall flow between blade rows in a compact multistage configuration possible, a miniature L-shaped five-hole probe was employed in this paper. This compact tip structure, realized by laser-printing instead of the conventional machining technique, reduces the blockage effect of this intrusive measurement on the flow and ensures high spatial resolution. The zonal method is introduced to extend the usable flow angle range up to 60 degrees. A local least-squares interpolation technique is utilized to acquire flow angle and static/total pressure. In order to improve accuracy for the points located at the sector boundary, the overlap region method is included in the interpolation. Additional test data indicate that the maximum error in flow angle is nearly within 1 degree, and the maximum errors of total pressure and static pressure are 0.56% and 1.9% respectively. The application in a low-speed multistage axial compressor indicates that the zonal method can decrease the number of points exceeding the measurable flow range and is of great significance for the end-wall flow measurement, especially for the near-stall condition. Compared with the traditional method, the proportion of available data for the near-stall state measurement was increased by 18% by using the zonal method.