Owing to the manufacturing and assembly error or the fatigue of long-time operation, nonaxisymmetric tip clearance is actually a common phenomenon in compressors. It is also well accepted that tip leakage flow, associated with tip clearance size and loading, has a strong influence on the performance and stall inception of compressors. The work of this paper, based on an eccentric compressor with/without inlet swirl distortion, is aimed at strengthening the understanding of stall inception for a real geometry compressor experimentally. Results indicate that rotor tip blockage and flow unsteadiness vary evidently around the circumference. For this compressor, the maximum tip flow unsteadiness and blockage happens at the location near the minimum clearance under the condition of clean inlet flow. Before the occurrence of stall inception, disturbances arise and vanish intermittently within the region of high unsteadiness. However, it fails to rotate due to the inhibition of the low unsteadiness region. Once the most robust region is no longer able to suppress disturbances, stability finally breaks down and stall inception generates. After exerting inlet paired swirl, unsteadiness within the region of positive preswirl decreases significantly and the maximum unsteadiness location shifts, while the increase for the region with negative preswirl is nearly negligible. As a result, stall margin of the compressor is improved.
In this paper, an experimental study was carried out on the rotating instability in an axial compressor subjected to inlet steady paired swirl distortion. In order to deepen the understanding of the rotating stall mechanism under inlet steady paired swirl distortion, the dynamic-wall static pressure near the rotor tip was monitored to characterize the flow in the rotor tip region at different circumferential stations. In the experiment, the dynamic characteristics of the rotor tip flow field at a stable operating point and during the process from the stable point to complete stall were measured. The results indicated that for the compressor with a 2 mm rotor tip clearance, the inlet paired swirl distortion induced rotating instability (RI) near the stall point, causing the compressor to enter stall in advance. Compared with the RI intensity of the clean inlet, the distortion with a swirling blade stagger angle (αst) of ±20° increased the RI intensity up to 69.8%, while for αst equal to ±40°, the RI intensity increased at most by 135.8%. As the rotor tip clearance increased to 3 mm, the co-rotating swirl in the paired swirl distortion inhibited the appearance of RI, while the counter-rotating part aggravated the development of RI. At the beginning, the process of the compressor rotating stall involved the alternation of short-scale disturbance and long-scale disturbance. The co-rotating swirl weakened the perturbation propagated from the counter-rotating swirl sector. Once the inhibition was no longer present, the short-scale disturbance rapidly developed into a long-scale disturbance and then entered the rotating stall.
It is well known that variations in stagger angle between rotor blades affect compressor performance. In this paper, the stagger angle of blade No. 8 is increased or decreased by six degrees for non-uniformity, and the influence of rotor non-uniformity caused by the change in only one blade stagger angle on the performance and stability of the compressor is investigated. The experimental results show that whether the local rotor stagger angle increases or decreases, the compressor stability will deteriorate. If the stagger angle of blade No. 8 is reduced by six degrees, the flow coefficient at the stall point increases by 8.5%. If the stagger angle of blade No. 8 is increased by six degrees, the flow coefficient at the stall point increases by 1.5%. The reason for the deterioration of compressor stability caused by the local non-uniform rotor stagger angle is explored. When the stagger angle of rotor blade No. 8 deviates from the designed state, the load of blade No. 8 and the surrounding blades will change. The load on rotor blade No. 8 increases when the stagger angle decreases. In the near-stall condition, blade No. 8 becomes the “dangerous blade” that triggers the stall. As the stagger angle of rotor blade No. 8 increases, the load on blade No. 8 decreases. However, the load on blade No. 9 increases due to flow redistribution and blade No. 9 becomes a “dangerous blade” that triggers stall. The “dangerous blade” caused by the non-uniformity of stagger angle is the direct reason for the advance of the compressor rotating stall.
To make measurement of end-wall flow between blade rows in a compact multistage configuration possible, a miniature L-shaped five-hole probe was employed in this paper. This compact tip structure, realized by laser-printing instead of the conventional machining technique, reduces the blockage effect of this intrusive measurement on the flow and ensures high spatial resolution. The zonal method is introduced to extend the usable flow angle range up to 60 degrees. A local least-squares interpolation technique is utilized to acquire flow angle and static/total pressure. In order to improve accuracy for the points located at the sector boundary, the overlap region method is included in the interpolation. Additional test data indicate that the maximum error in flow angle is nearly within 1 degree, and the maximum errors of total pressure and static pressure are 0.56% and 1.9% respectively. The application in a low-speed multistage axial compressor indicates that the zonal method can decrease the number of points exceeding the measurable flow range and is of great significance for the end-wall flow measurement, especially for the near-stall condition. Compared with the traditional method, the proportion of available data for the near-stall state measurement was increased by 18% by using the zonal method.