Ti, Cr dual-element-doped LiMn1.5Ni0.5O4 (LNMO) cathode materials (LTNMCO) were synthesized by a simple high-temperature solid-phase method. The obtained LTNMCO shows the standard structure of the Fd3̅m space group, and the Ti and Cr doped ions may replace the Ni and Mn sites in LNMO, respectively. The effect of Ti–Cr doping and single-element doping on the structure of LNMO was studied by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM) characteristics. The LTNMCO exhibited excellent electrochemical properties with a specific capacity of 135.1 mAh·g–1 for the first discharge cycle and a capacity retention rate of 88.47% at 1C after 300 cycles. The LTNMCO also has high rate performance with a discharge capacity of 125.4 mAh·g–1 at a 10C rate, 93.55% of that at 0.1C. In addition, the CIV and EIS results show that the LTNMCO showed the lowest charge transfer resistance and the highest diffusion coefficient of lithium ions. The enhanced electrochemical properties may be due to a more stable structure and an optimized Mn3+ content in LTNMCO through TiCr doping.
With the aim of obtaining a refining flux that is stable and provides effective refining of aluminum melt, a new strategy of designing the flux composition has been proposed. Ten fluxes were designed, by selecting ten molten salt compounds according to their thermophysical parameters, physical properties, and thermodynamic analysis. The melting points of the ten fluxes, and the phases transformation of the fluxes after melting, were studied by DSC and XRD, respectively. The contact angles between four groups of fluxes and alumina at refinement temperatures were studied, and the effect of refinement was characterized by a metallographic microscope. The process of the fluxes removing inclusions and degassing was analyzed thermodynamically. The research findings indicate that flux #10 (11.0 wt.%NaF, 29.5 wt.%NaCl, 46.5 wt.%Na2CO3, 3.0 wt.%CaF2, 10.0 wt.%Na3AlF6) has a melting point (562.2 °C) below the refining temperature. At the refining temperature (760 °C), flux #10 has the lowest contact angle, of 12.78°. In addition, compared to that of flux STJ–A3, currently used in practice, flux #10 has a better refining effectiveness, with the pores and inclusions content of the sample being reduced to 1.11% from 2.96%.
An inhomogeneous microstructure induced by high rotating speed submerged friction stir processing (HRS-SFSP) on 6061 aluminum alloy was researched in detail.The microstructures of the aluminum alloy processing zone were characterized by electron backscattered diffraction (EBSD) and transmission electron microscope (TEM) qualitatively and quantitatively.The results show that the recrystallization proportion in the inhomogeneous structure of the processing zone is 14.3%, 37.8% and 35.9%, respectively. Different degrees of grain deformation can affect the dislocation and lead to the formation of a plastic–elastic interface. At the same time, the second-phase particles in the processing zone were inhomogeneity and relatively, which further promotes the plastic–elastic interface effect. The plastic–elastic interface can significantly improve the strength of aluminum alloy, whileat the same time, rely on recrystallized grains to provide enough plasticity. When the rotation speed was 3600 r/min, the strength and ductility of the aluminum alloy after HRS-SFSP were increased by 48.7% and 10.2% respectively compared with that of BM. In all, the plastic–elastic interface can be formed by using high rotating speed submerged friction stir processing, and the strength-ductility synergy of aluminum alloy can be realized at the plastic–elastic interface.
Microstructure is a significant factor that influences the mechanical properties of alloys. The effect of multiaxial forging (MAF) and subsequent aging treatment on the precipitated phases of Al-Zn-Mg-Cu alloy remains unclear. Therefore, an Al-Zn-Mg-Cu alloy was processed by means of solid solution and aging treatment, and MAF and aging treatment in this work, and the composition and distribution of precipitated phases were characterized in detail. The MAF results for dislocation multiplication and grain refinement were found. The high density of dislocation greatly accelerates the nucleation and growth of precipitated phases. Thus, the GP-zones almost transform into precipitated phases during subsequent aging. The MAF and aging alloy has more precipitated phases than the solid solution and aging treated alloy. The precipitates on the grain boundary are coarse and discontinuously distributed due to dislocation and grain boundary promoting the nucleation, growth and coarsening of the precipitates. The hardness, strength, ductility and microstructures of the alloy have been studied. Without compromising the ductility much, the MAF and aging alloy has higher hardness and strength, with values of 202 HV and 606 MPa, respectively, and an appreciable ductility of 16.2%.
Al-Ti-B intermediate alloys are widely used as grain refiners in aluminum alloys owing to the presence of Al3Ti and TiB2 phases. However, the existence of Zr in aluminum alloy melts often results in coarse grain size, leading to Al-Ti-B failure called Zr poisoning. There are three kinds of poisoning mechanisms related to TiB2, Al3Ti, and a combination of TiB2 and Al3Ti for Zr. First, Zr forms ZrB2 or Ti2Zr with TiB2 in Al-Ti-B to reduce the nucleation ability. Second, Zr existing in the aluminum melt with a high melting point Al3Zr then attracts Ti to reduce the dispersion of Ti as a growth inhibitor. Third, Zr reacts with Al3Ti on TiB2 surface to form Al3Zr, thereby increasing the degree of mismatch with Al and diminishing the refiner’s ability as a nucleation substrate. To gain a better understanding of the mechanism of Zr poisoning, the first principle was used in this study to calculate the adhesion works (ZrB2//Al3Ti), (Ti2Zr//Al3Ti), (Al3Zr//Al3Ti), (Al3Ti//Al), (TiB2//Al3Zr), and (Al3Zr//Al), as well as the surface energy of Al3Zr and adsorption energies of Al to Al3Ti or Al3Zr. The results demonstrated that Zr poisoning originated from the second guess. Zr element exiting in aluminum melt led to the formation of an Al3Zr (001) surface. The interfacial adhesion work of Al3Zr (001)//Al3Ti (001) was not weaker than that of TiB2//Al3Ti. As a result, Al3Zr first combined with Al3Ti to significantly decline the adsorption of Al3Ti (001) on Al, losing its role as a nucleating agent and grain coarsening. Overall, to prevent failure of the grain refiner in Zr containing aluminum melt, the adhesion work interface between the generated phase of the grain refiner and Al3Zr must remain lower to avoid the combination of the generated phase of grain refiner with Al3Zr. In sum, these findings look promising for evaluating future effects of grain refinement in Zr containing aluminum melt.
The effect of Er-rich precipitates on microstructure and electrochemical behavior of the Al–Zn–In anode alloy is investigated. The results showed that with the increase in Er content, the microstructure was refined, the amount of interdendritic precipitates gradually increased, and the morphology changed from discontinuous to continuous network gradually. With the addition of Er element, the self-corrosion potential of the Al–5Zn–0.03In–xEr alloy moved positively, the self-corrosion current density decreased, and the corrosion resistance increased. When the Er content was less than 1 wt.%, the addition of Er improved the dissolution state of the Al–5Zn–0.03In–xEr alloy, and increased the current efficiency of the Al–5Zn–0.03In–xEr alloy. When the Er content was more than 1 wt.%, the current efficiency was reduced. The major precipitate of the alloy was Al3Er. According to the element composition of Al3Er in the Al–Zn–In–Er alloy, the simulated-segregated-phase alloy was melted to explain the effect of Al3Er segregation on the electrochemical behavior of alloys, and the polarization curve and AC impedance spectrum of the simulated-segregated-phase alloy and the Al–Zn–In alloy were measured. The results showed that Al3Er was an anodic segregation phase in the Al–Zn–In–Er alloy, and the preferential dissolution of the segregation phase would occur in the alloy, but the Al3Er phase itself was passivated in the dissolution process, which inhibited the further activation of the dissolution reaction of the Al–Zn–In–Er alloy to a certain extent.