More and more mega-complex bridge projects are being or will be built worldwide. At the same time, the design and construction of such projects involve more and more challenges, e.g., complex structural designs, complicated construction environments, etc. This research study aims to apply BIM (Building Information Modelling) to bridge projects to improve the efficiency and effectiveness of design and construction. Through the analysis of the characteristics of bridge projects and relevant, associated problems, a BIM-based solution to improving design and construction is developed, including conceptual design optimization, detailed design optimization, the optimization of construction sequences, construction scheduling, construction management, and construction process monitoring. Furthermore, a real-life bridge project is presented to demonstrate the feasibility and validity of the BIM-aided approach to design and construction. It is shown that BIM has the potential to improve the design and construction of bridge projects. It is expected that this research could contribute to the extensive application of BIM in mega-complex bridge projects to aid in design and construction in the future.Department of Building and Real Estat
1 June 2017 in Journal of Construction Engineering and Management
Quickly changing and complicated workplace conditions, which are typical of construction projects, have always been contributing to the poor safety record of the construction industry. However, few of the existing approaches to reviewing control measures take into account or effectively tackle these conditions. This paper introduces a three-level (i.e., individual hazards, hazard types, and generic hazards) hierarchical Bayesian model based on workers’ responses to proximity warnings of safety hazards to address the problem. The proposed model distinguishes between two uses of proximity warnings (i.e., as the primary control measure and as the secondary measure), uses observational response rates as input, takes into account prior knowledge of workers’ responses to similar hazards, and produces estimated response rates (ERRs). These ERRs are the primary indicator of the effectiveness of a given control measure as well as of the validity of a previously identified safety hazard. A 17-day field experiment was conducted to test the proposed approach, preliminarily using a location-based proximity warning system to warn workers of safety hazards and record their responses to warnings. The experimental results demonstrated the potential of the proposed approach. The limitations of the present analysis and the directions for future research are also discussed.
Accurate selection and location of mobile cranes is a critical issue on construction sites, being able to contribute to the improvement of the safety and efficiency of lifting operations. Considering the complexities and dynamics of construction sites, this study aimed to develop a useful approach for automated selection and localization of mobile cranes based on the simulation of crane operations. First, the information required for crane selection and localization is analyzed and extracted from BIM (building information modeling). Then, mainly considering the crane capacity, the initial crane type is selected with candidate location points. Based on the simulation of lifting operation at the candidate points, feasible location points and crane types are determined through three constraint checks (i.e., environment constraint, operation constraint, and safety constraint). Besides, two kinds of efficiency optimization, namely lifting time minimization and crane movement minimization, are presented to figure out the best location points from the feasible points. Finally, the proposed approach is validated using a case study. This research contributes to not only crane operation planning but also automatic construction simulation, thus supporting the implementation of intelligent construction in the future.
The construction industry has become one of the most hazardous industries worldwide. How to prevent construction accidents on site is attracting increasing and extensive attention. Traditional accident prevention methods depend primarily on safety training and site management. These are demonstrably not enough to support safety management, as evidenced by the high rate of construction accidents. As worker behavior is a key factor influencing accidents, this paper proposes a warning system of unsafe behavior by integrating Building Information Modeling (BIM) with Radio Frequency Identification (RFID) positioning technology. Through the investigation and classification of unsafe behaviors on site, the information demands of the warning system are analyzed and a prototype of the system is developed. Its functions are also tested in test bed trials, where it identified workers' locations on site in real time and responded to workers in unsafe situations, indicating that the system has a clear potential to improve safety management on site.
1 January 2012 in International Journal of Construction Management
The productivity of the construction industry worldwide has been declining over the past forty years. One approach to improving the situation is by the introduction of lean construction. The IKEA model has been shown to be beneficial when used in the construction context. A framework is developed in which the lean construction concept is embodied within the IKEA model by integrating Virtual Prototyping (VP) technology and its implementation is described and evaluated through a real-life case implementing the lean production philosophy. The operational flows of the IKEA model and lean construction are then compared to analyze the feasibility of IKEA-based lean construction. It is concluded that the successful application of the IKEA model in this context will promote the implementation of lean construction and improve the efficiency of the industry.