Lucie Pilsová

Mrs. Lucie Pilsová

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 October 2023 in International Journal of Fatigue
Verified
Journal Article
Closed access
BMBartošák Michal
Bartošák Michal
IŠIvo Šulák
Ivo Šulák
JHJakub Horváth
Jakub Horváth
MJMichal Jambor
Michal Jambor
LPLucie Pilsová
Lucie Pilsová

16 January 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
VMVladimír Mára
Vladimír Mára
JKJan Krčil
Jan Krčil
LPLucie Pilsová
Lucie Pilsová

7 January 2022 in Materials
Verified
Journal Article
Open access
PDF file
LPLucie Pilsová
Lucie Pilsová
JHJakub Horváth
Jakub Horváth
VMVladimír Mára
Vladimír Mára
This paper describes the influence of technological treatments (i.e., bending or welding) on the structural stability of SUPER304H austenitic steel used in reheaters and superheaters in fossil fuel power plants. Although the worldwide trend is transitioning to green power sources, the lifetime of existing power plants has to be prolonged until the transition is complete. Experimental material was tested in as-received state (straight tubes), bends, and homogeneous weld joints. Part of the specimens was solution-annealed after the technological operation. Afterwards, all the samples were thermally aged in furnace (650, 675 and 700 °C) for 7560–20,000 h. For comparison, bent specimens were placed at experimental sites on an operating powerplant for 10,000+ h. The long-term aging causes the formation of Cr-based carbides on the grain boundaries along with the Fe-Cr sigma phase. Combination of elevated temperature and residual stress accelerates formation of the sigma phase. This can be prevented by solution-annealing after bending. Mechanical properties were evaluated by Vickers hardness and tensile tests. The microstructure was observed using light optical microscopy (LOM) and scanning electron microscopy (SEM) with the energy-dispersive X-ray detector (EDXS). Electron backscatter diffraction (EBSD) and X-ray powder diffraction (XRPD) were used to characterize the brittle phases.

28 June 2022 in Defect and Diffusion Forum
Verified
Journal Article
Closed access
PDF file
LPLucie Pilsová
Lucie Pilsová
VMVladimír Mára
Vladimír Mára
MSMarie Svobodová
Marie Svobodová
JHJakub Horváth
Jakub Horváth
This paper describes a metallographic preparation of the heat-exchanger austenitic stainless steels, i.e., SUPER 304H, HR3C and Sanicro 25. The as-received materials delivered after the solution annealing are very resistant to the chemical etchants. Therefore, it is more efficient to optimize the parameters of the electrolytic etching in the acidic or basic electrolytes. After the materials’ operation under elevated temperatures (600–750 °C), the microstructure is easier to etch due to the reduction of corrosion resistance. For the following analyses, it is necessary to think of the etching purpose in advance. For the grain size determination, it is sufficient to use electrolytic etching in the oxalic acid solution or chemical swabbing in the combination of 15 ml HCl, 10 ml acetic acid and 5 ml HNO3. For the image analysis of the intermetallics, the previous methods can be too invasive and give skewed results. In many cases, this leads to the overetching and thus removal of the observed particles (intermetallics, carbides, etc.). It is suitable to use selective etching methods or only polishing for a more precise evaluation, e.g., electron microscopy.

1 January 2024
Verified
Conference Paper
Open access
EGEliška GALČÍKOVÁ
Eliška GALČÍKOVÁ
JKJan Krčil
Jan Krčil
VMVladimír Mára
Vladimír Mára
LPLucie Pilsová
Lucie Pilsová
JRJiří REŽNAR
Jiří REŽNAR
JDJaromir Drapala
Jaromir Drapala