In this paper, we study the light scalar and pseudoscalar invisible particles in the flavor changing neutral current processes of the Bc meson. Effective operators are introduced to describe the couplings between quarks and light invisible particles. The Wilson coefficients are extracted from the experimental results of the B and D mesons, which are used to predict the upper limits of the branching fractions of the similar decay processes for the Bc meson. The hadronic transition matrix element is calculated with the instantaneously approximated Bethe-Salpeter method. The upper limits of the branching fractions when mχ taking different values are presented. It is found that at some region of mχ, the channel Bc → Ds(*)χχ has the largest upper limit which is of the order of 10−6, and for Bc → Ds*χχ†, the largest value of the upper limits can achieve the order of 10−5. Other decay modes, such as Bc → D(*)χχ(†) and Bc → B(*)χχ(†), are also considered.
With the deepening of drilling depth, the difficulty of drilling engineering increases gradually due to the complex geological conditions. The traditional mechanical drilling method shows the problems of high energy consumption, low efficiency, long cycle and high cost. Because of the characteristics of rock, the high abrasiveness of rock causes great wear to the bit, which becomes an important factor affecting the drilling rate. High voltage electric pulse (Abbreviated as HVEP later in this paper) drilling technology is a new technology developed in the past several decades. The technology uses plasma channel, water jet or shock wave generated by high voltage electric pulse discharge to break rock. It has the characteristics of environmental protection, directional breaking, easy control of rock breaking process and fast speed in the face of complex hard rock. In this paper, the mechanism and technology of rock breaking by high voltage electric pulse method in deep drilling are studied, and the functional test is carried out.
Mechanical equipment in the field of aerospace that is used only once is called disposable machinery. As a piece of typical disposable machinery, disposable harmonic gear exhibit stiffness failure with a large load. This manuscript distinguishes disposable harmonic gear from conventional harmonic gear in terms of the application environment and structure. Then, this paper determines the single-tooth stiffness of the disposable harmonic gear under full load by using the non-uniform beam model and the improved energy method. In addition, the multi-tooth meshing in the disposable harmonic drive is considered, and the improved energy method is modified. Besides, the normal contact force and comprehensive elastic displacement at each meshing position are calculated according to the finite element model. Additionally, curves of the single-tooth stiffness and the comprehensive meshing stiffness are obtained. The theoretical results of the modified analytical method and FEM are compared to verify the correctness of the proposed method in terms of calculating the meshing stiffness of the disposable harmonic drive. Finally, FEM is used to obtain the failure form of the disposable harmonic gear under overload.
Mechanical equipment that will not be reused is defined as disposable machinery. Disposable harmonic drives (HDs) are commonly used in the field of aerospace and are sensitive to payloads. Reasonable calculation of the gear strength is essential for structural design. A method of calculating the contact characteristics of HDs under full load by combining a surface contact model with a three-dimensional finite element model (FEM) is proposed in this work. The mathematical model was established for calculating the no-load backlash of conventional and disposable harmonic gears after assembly. Afterward, the tooth load distribution and surface contact stress were determined using the Hertz contact theory. Finally, ABAQUS software was used to establish the FEM of the disposable HD, and the results were compared with those obtained from the theoretical model. The results revealed that the disposable harmonic gear can realize short-term transmission under full load.
In this paper we study the semileptonic decays of $B^\ast$, $B_s^\ast$, and $B_c^\ast$ by using the Bethe-Salpeter method with instantaneous approximation. Both the $V\to Pl^-\bar\nu_l$ and $V\to Vl^-\bar\nu_l$ cases are considered. The largest partial width of these channels is of the order of $10^{-14}$ GeV. The branching ratios of these semileptonic decays are also estimated by using the partial width of the one photon decay channel to approximate the total width. For $B^{\ast-}\to D^{(\ast)0}e^-\bar\nu_e$ and $B_s^{\ast0}\to D_s^{(\ast)+}e^-\bar\nu_e$, the branching ratios are of the order of $10^{-8}$ and $10^{-7}$, respectively. For $B_c^{\ast-}$, the $J/\psi e^-\bar\nu_e$ and $B_s^{\ast0}e^-\bar\nu_e$ channels have the largest branching ratio, which is of the order of $10^{-6}$.
In this paper, with the framework of (p)NRQCD and SCET, the processes $B_c\to M_1 M_2$ are investigated. Here $M_{1(2)}$ denotes the light charmless meson, such as $\pi$, $\rho$, $K$ or $K^*$. Based on the SCET power counting rules, the leading transition amplitudes are picked out, which include $A_{wA}^2$, $A_{wB}^2$, $A_{wC}^2$, $A_{wD}^2$ and $A_{c}^0$. From SCET, their factorization formulae are proven. Based on the obtained factorization formulae, in particular, the numerical calculation on $A_{wB}^2$ is performed.