Yuefeng Li

Yuefeng Li


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2023 in Energies
Verified
Journal Article
Open access
PDF file
QZQingyu Zhang
Qingyu Zhang
GWGuanglin Wang
Guanglin Wang
XPXudong Pan
Xudong Pan
YLYuefeng Li
Yuefeng Li
JHJianqi He
Jianqi He
JYJuesuan Yang
Juesuan Yang
With the deepening of drilling depth, the difficulty of drilling engineering increases gradually due to the complex geological conditions. The traditional mechanical drilling method shows the problems of high energy consumption, low efficiency, long cycle and high cost. Because of the characteristics of rock, the high abrasiveness of rock causes great wear to the bit, which becomes an important factor affecting the drilling rate. High voltage electric pulse (Abbreviated as HVEP later in this paper) drilling technology is a new technology developed in the past several decades. The technology uses plasma channel, water jet or shock wave generated by high voltage electric pulse discharge to break rock. It has the characteristics of environmental protection, directional breaking, easy control of rock breaking process and fast speed in the face of complex hard rock. In this paper, the mechanism and technology of rock breaking by high voltage electric pulse method in deep drilling are studied, and the functional test is carried out.

10 April 2022 in Machines
Verified
Journal Article
Open access
PDF file
YZYuxin Zhang
Yuxin Zhang
XPXudong Pan
Xudong Pan
YLYuefeng Li
Yuefeng Li
GWGuanglin Wang
Guanglin Wang
GWGuicheng Wu
Guicheng Wu
Mechanical equipment in the field of aerospace that is used only once is called disposable machinery. As a piece of typical disposable machinery, disposable harmonic gear exhibit stiffness failure with a large load. This manuscript distinguishes disposable harmonic gear from conventional harmonic gear in terms of the application environment and structure. Then, this paper determines the single-tooth stiffness of the disposable harmonic gear under full load by using the non-uniform beam model and the improved energy method. In addition, the multi-tooth meshing in the disposable harmonic drive is considered, and the improved energy method is modified. Besides, the normal contact force and comprehensive elastic displacement at each meshing position are calculated according to the finite element model. Additionally, curves of the single-tooth stiffness and the comprehensive meshing stiffness are obtained. The theoretical results of the modified analytical method and FEM are compared to verify the correctness of the proposed method in terms of calculating the meshing stiffness of the disposable harmonic drive. Finally, FEM is used to obtain the failure form of the disposable harmonic gear under overload.

26 January 2022 in Machines
Verified
Journal Article
Open access
PDF file
YZYuxin Zhang
Yuxin Zhang
GWGuanglin Wang
Guanglin Wang
XPXudong Pan
Xudong Pan
YLYuefeng Li
Yuefeng Li
Mechanical equipment that will not be reused is defined as disposable machinery. Disposable harmonic drives (HDs) are commonly used in the field of aerospace and are sensitive to payloads. Reasonable calculation of the gear strength is essential for structural design. A method of calculating the contact characteristics of HDs under full load by combining a surface contact model with a three-dimensional finite element model (FEM) is proposed in this work. The mathematical model was established for calculating the no-load backlash of conventional and disposable harmonic gears after assembly. Afterward, the tooth load distribution and surface contact stress were determined using the Hertz contact theory. Finally, ABAQUS software was used to establish the FEM of the disposable HD, and the results were compared with those obtained from the theoretical model. The results revealed that the disposable harmonic gear can realize short-term transmission under full load.

12 April 2017 in International Journal of Systems Science
Verified
Journal Article
Closed access
CLChengcheng Li
Chengcheng Li
YLYuefeng Li
Yuefeng Li
GWGuanglin Wang
Guanglin Wang
The work presented in this paper seeks to address the tracking problem for uncertain continuous nonlinear systems with external disturbances. The objective is to obtain a model that uses a reference-based output feedback tracking control law. The control scheme is based on neural networks and a linear difference inclusion (LDI) model, and a PDC structure and H∞ performance criterion are used to attenuate external disturbances. The stability of the whole closed-loop model is investigated using the well-known quadratic Lyapunov function. The key principles of the proposed approach are as follows: neural networks are first used to approximate nonlinearities, to enable a nonlinear system to then be represented as a linearised LDI model. An LMI (linear matrix inequality) formula is obtained for uncertain and disturbed linear systems. This formula enables a solution to be obtained through an interior point optimisation method for some nonlinear output tracking control problems. Finally, simulations and comparisons are provided on two practical examples to illustrate the validity and effectiveness of the proposed method.

1 August 2024 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
YZYizhen Zheng
Yizhen Zheng
YLYuefeng Li
Yuefeng Li
WWWentao Wu
Wentao Wu
FMFanwei Meng
Fanwei Meng
CCChangyu Chen
Changyu Chen

23 July 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
YLYuefeng Li
Yuefeng Li
MWMin Wang
Min Wang
ZAZhongyu An
Zhongyu An