Mohamed Abdulgader

Dr. Mohamed Abdulgader


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2019 in Coatings
Verified
Journal Article
Open access
PDF file
WTWolfgang Tillmann
Wolfgang Tillmann
OKOmar Khalil
Omar Khalil
MAMohamed Abdulgader
Mohamed Abdulgader
In the thermal spraying process, the porosity of ceramic coatings contributes directly to the efficiency of the thermal insulation. The size, shape, and distribution of the pores determine the level of both thermal and sintering resistance. In this work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated with the same spraying parameters using alumina powders with fine, medium, and coarse particle size. The microstructure of the obtained coatings was analyzed regarding the obtained total porosity, pore size, and pore shape. It was found that it is expedient to divide the pore size range into fine, medium, and large sizes. The shape was characterized with regard to the circularity aspect. In this way, all types of cracks can be considered as oblate pores and were included in the calculation of the total porosity. In the case of using fine feedstock powder, the densest coatings were produced among all coatings, and the fraction of fine pores and cracks are thereby substantially higher. However, the total porosity increases with increasing feedstock powder size. A connection was also made between thermal insulation and porosity fraction which includes fine pores and cracks.

17 July 2020 in Coatings
Verified
Journal Article
Open access
PDF file
WTWolfgang Tillmann
Wolfgang Tillmann
LHLeif Hagen
Leif Hagen
MAMohamed Abdulgader
Mohamed Abdulgader
MKMark Dennis Kensy
Mark Dennis Kensy
MPMichael Paulus
Michael Paulus
Studies have already established that the mechanical properties of Babbitt coatings significantly depend on the microstructural characteristics, such as the amount and distribution of intermetallic compounds dispersed in a soft solid solution matrix. For Sn–Sb–Cu-based Babbitt coatings, the formation of SbSn- and CuSn-based precipitates has a substantial influence on the resulting microhardness and thus determines the maximum load carrying capacity. Thermal spraying of Sn-based Babbitt coatings results in a relatively more refined structure of these precipitates than in common manufacturing processes, such as casting, due to the thermal processing conditions. This study aims to evaluate the effect of the temperature of the propellant gas and substrate temperature on the microstructural characteristics of Sn–Sb–Cu-based Babbitt coatings deposited by low pressure cold spraying (LPCS). The deposits were examined for their phase composition, microhardness and mesoscopic structure. It was found that the coatings were mainly composed of Sb2Sn23, Sb0.49Sn0.51 and Sorosite (CuSn or CuSb0.115Sn0.835), regardless of the substrate temperature or temperature of the propellant gas to be investigated. For a gas temperature above 300 °C, an increased microhardness was observed, which correlates with the appearance of a more homogenous distribution of Sb0.49Sn0.51 dispersed in a soft Sn-rich solid solution matrix.

3 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
MMMichael Milz
Michael Milz
AWAndreas Wirtz
Andreas Wirtz
MAMohamed Abdulgader
Mohamed Abdulgader
DBDirk Biermann
Dirk Biermann
WTWolfgang Tillmann
Wolfgang Tillmann
Frank WaltherFrank Walther
Frank Walther
Structural elements for applications in maritime environments, especially offshore installations, are subjected to various stresses, such as mechanical loads caused by wind or waves and corrosive attacks, e.g., by seawater, mist and weather. Thermally sprayed ZnAl coatings are often used for maritime applications, mainly due to good corrosion protection properties. Machine hammer peening (MHP) has the potential to increase fatigue and corrosion fatigue resistance of ZnAl coatings by adjusting various material properties such as hardness, porosity and roughness. This study investigates the fatigue behavior of twin wire arc sprayed and MHP post-treated ZnAl4 coatings. Unalloyed steel (S355 JRC+C) was selected as substrate material and tested as a reference. MHP achieved the desired improvements in material properties with increased hardness, decreased roughness and uniform coating thickness. Multiple and constant amplitude tests have been carried out to evaluate the fatigue capability of coating systems. In the high cycle fatigue regime, the additional MHP post-treatment led to an improvement of the lifetime in comparison to pure sandblasted specimens. The surface was identified as a crack initiation point. ZnAl coating and MHP post-treatment are suitable to improve the fatigue behavior in the high cycle fatigue regime compared to uncoated specimens.

Verified
Journal Article
Open access
PDF file
MMMichael Milz
Michael Milz
AWAndreas Wirtz
Andreas Wirtz
MAMohamed Abdulgader
Mohamed Abdulgader
AKAnke Kalenborn
Anke Kalenborn
DBDirk Biermann
Dirk Biermann
Frank WaltherFrank Walther
Frank Walther
Offshore installations, e.g., offshore wind turbines and pipelines, are exposed to various mechanical loads due to wind or waves and corrosive loads such as seawater or mist. ZnAl-based thermal sprayed coatings, often in conjunction with organic coatings, provide sufficient corrosion protection and are well established for applications in marine environments. In this study, machine hammer peening (MHP) is applied after twin wire arc spraying to improve corrosion fatigue behavior through increased hardness, reduced porosity, and roughness compared to as-sprayed coatings. Mn-alloyed structural steel S355 J2 + C with and without ZnAl4 coating as well as with MHP post-treated ZnAl4 coating were cyclically loaded in 3.5% NaCl solution. MHP leads to a uniform coating thickness with lower porosity and roughness. ZnAl4 coating and MHP post-treatment improved corrosion fatigue behavior in the high cycle fatigue regime with an increase of the stress amplitude, applied to reach a number of cycles 1.2 × 106, up to 115% compared to sandblasted specimens. Corrosive attack of the substrate steel was successfully avoided by using the coating systems. Stress- and microstructure-dependent corrosion fatigue damage mechanisms were evaluated by mechanical and electrochemical measurement techniques.

27 December 2021 in Coatings
Verified
Journal Article
Open access
PDF file
WTWolfgang Tillmann
Wolfgang Tillmann
MAMohamed Abdulgader
Mohamed Abdulgader
AWAndreas Wirtz
Andreas Wirtz
MMMichael Milz
Michael Milz
DBDirk Biermann
Dirk Biermann
Frank WaltherFrank Walther
Frank Walther
In the twin wire arc spraying (TWAS) process, it is common to use compressed air as atomizing gas. Nitrogen or argon also are used to reduce oxidation and improve coating performance. The heat required to melt the feedstock material depends on the electrical conductivity of the wires used and the ionization energy of both the feedstock material and atomization gas. In the case of ZnAl4, no phase changes were recorded in the obtained coatings by using either compressed air or argon as atomization gas. This fact has led to the assumption that the melting behavior of ZnAl4 with its low melting and evaporating temperature is different from materials with a higher melting point, such as Fe and Ni, which also explains the unexpected compressive residual stresses in the as-sprayed conditions. The heavier atomization gas, argon, led to slightly higher compressive stresses and oxide content. Compressed air as atomization gas led to lower porosity, decreased surface roughness, and better corrosion resistance. In the case of argon, Al precipitated in the form of small particles. The post-treatment machine hammer peening (MHP) has induced horizontal cracks in compressed air sprayed coatings. These cracks were mainly initiated in the oxidized Al phase.

Verified
Journal Article
Open access
PDF file
AWAndreas Wirtz
Andreas Wirtz
MAMohamed Abdulgader
Mohamed Abdulgader
MMMichael Milz
Michael Milz
WTWolfgang Tillmann
Wolfgang Tillmann
Frank WaltherFrank Walther
Frank Walther
DBDirk Biermann
Dirk Biermann
Structural elements of offshore facilities, e.g., offshore wind turbines, are subject to static and dynamic mechanical and environmental loads, for example, from wind, waves, and corrosive media. Protective coatings such as thermal sprayed ZnAl coatings are often used for protection, mainly against corrosive stresses. The Machine Hammer Peening (MHP) process is an innovative and promising technique for the post-treatment of ZnAl coating systems that helps reducing roughness and porosity and inducing compressive residual stresses. This should lead to an enhancement of the corrosion fatigue behavior. In this paper, the effect of a thermally assisted MHP process was investigated. The softening of the coating materials will have a direct effect on the densification, residual porosity and the distribution of cracks. The investigation results showed the influence of thermally assisted MHP on the surface properties, porosity, residual stresses, and hardness of the post-treated coatings. The best densification of the coating, i.e., the lowest porosity and roughness and the highest compressive residual stresses, were achieved at a process temperature of 300 °C. A further increase in temperature on the other hand caused a higher porosity and, in some cases, locally restricted melting of the coating and consequently poorer coating properties.