The continuously intensifying demand for high-performance and miniaturized semiconductor devices has pushed the aggressive downscaling of field-effect transistors (FETs) design. However, the detrimental short-channel effects and the fundamental limit on the sub-threshold swing (SS) in FET have led to a drastic increase in static and dynamic power consumption. The operational limit of nanoscale transistors motivates the exploration of post-CMOS devices like Tunnel FET (TFET), having steeper SS and immunity toward short channel effects. Thus the field of nanoscale 2D-TFET has gained compelling attention in recent times. The nanoscale TFET, with two-dimensional (2D) semiconductor materials, has shown a significant improvement in terms of higher on-state current and lower sub-threshold swing. In this context, the review presented here has comprehensively covered the gradual development and present state-of-arts in the field of nanoscale 2D-TFET design. The relative merits and demerits of each class of 2D materials are identified, which sheds light on the specific design challenges associated with individual 2D materials. Subsequently, the potential device/material co-optimization strategies for the development of efficient TFET designs are highlighted. Next, the experimental development in 2D-TFET design is discussed, and specific synthesis/fabrication challenges for individual material systems are indicated. Finally, an extensive comparative performance study is presented between the simulated as well as experimentally reported potential 2D materials and state-of-the-art bulk material-based TFETs.
31 March 2021 in IEEE Transactions on Electron Devices
Leveraging laser-induced graphene (LIG) in various flexible polymer electronics applications is becoming tremendously popular. LIG is porous multilayer graphene generated by a single-step process using infrared CO₂ laser onto the carbon-based polymers. In this article, a direct LIG printed microstrip patch antenna operating at the 5.8-GHz unlicensed band is presented. Based on simulations, the proposed design exhibited the desired unidirectional radiation characteristics with a measured gain of 1.82 dBi at the resonant frequency. The LIG-based rectangular patch was printed using the CO₂ laser by selective reduction of polyimide (PI) sheet. The chemical properties of LIG were examined using various structural and morphological characterization techniques, which confirmed the formation of multilayer graphene. The sensitivity of the patch antenna was analyzed for measuring strain and its effect on LIG. By harnessing LIG on flexible material such as PI sheet, the antenna exhibited a threshold increase in sensitivity. The proposed sensor shows a sensitivity of 14.08 and 11.34 for compressive and tensile strain, respectively. Inspired by the significant sensitivity, the fabricated device has been examined for human motion monitoring by attaching it to the human hand for practical usage in real-time applications. The proposed antenna-based sensor reduces the number of components by eliminating external wiring and onboard battery. Moreover, it serves as both the sensing and wireless data transmitting element. Overall, this work demonstrates designing a compact, easy-to-fabricate, sensitive, and flexible antenna-based Internet of Things (IoT) sensor for motion detection, structural health monitoring, and industrial strain sensing applications.
29 March 2022 in ACS Applied Materials & Interfaces
Electronic skin has attracted a lot of interest in recent years due to its ability to mimic human skin and also its excellent conformability. Even though there are reports on electronic skin, the major issue that still needs to be resolved is achieving multifunctional sensing at the same time as ultra-high sensitivity. Hence, there is an immediate requirement to develop inexpensive, highly sensitive, and superior performance piezoresistive multifunctional sensors that mimic skin. Herein, an as synthesized pure MXene (Ti3C2Tx) colloidal solution was used to deposit a thin film on flexible polyurethane foam, forming a three-dimensional conductive network with an ultra-high sensitivity of ∼34.24 kPa−1 (1.477–3.185 kPa of applied pressure range) and an elevated gauge factor of ∼323.59 (5–20% of applied strain range). Further merits such as reproducibility, low cost, high scalability, and excellent stability after 2500 cycles imply the sturdiness of the fabricated device. The remarkable sensing efficiency can be attributed to the strong interaction of Ti3C2Tx and PU foam, the inherent 3D network of PU coupled with the excellent electrical properties of Ti3C2Tx, and the interconnection of the unconnected branches present in the internal framework of PU-foam, which indicates the existence of more conduction paths. Besides, the fabricated Ti3C2Tx was deposited on cellulose paper to be utilized as a temperature sensor which displayed ∼2.22 × 10−3 °C−1 TCR and 29.43 meV activation energy. Lastly, real time applications for the fabricated device are investigated including detecting an unknown position of an object and human gestures. The successful demonstration of the low-cost, flexible Ti3C2Tx based piezoresistive sensor has shown innovative applications in biomedical, security, educational, and health sectors.