This paper proposes an all-in-one system for hyperloop that conducts propulsion, levitation, and guidance. Currently demand on high-speed long-distance transportation is increasing, so that hyperloop is getting attention and studied hard globally. Hyperloop is a new innovative transportation in which a levitated subsonic speed train travels through a vacuum cylindrical tube. Hyperloop needs functions of propulsion, levitation, and guidance for its service, and many devices are necessary for those functions. In the tube, a constrained space, many devices make the entire system complicated, and the size of the vehicle and tube are increased. Therefore, the costs of maintenance, manufacture, and construction are increased and control of each device becomes very difficult. But a non-symmetric double-sided linear induction motor (NSDLIM), the subject of this paper, is an all-in-one system that could conduct all functions. In this paper, the concept of NSDLIM was introduced and its possibility was suggested. Requirements of NSDLIM were investigated considering very high acceleration, velocity, and low air pressure. An NSDLIM model was designed and analyzed by using the finite-element method. Then, NSDLIM parameters that affect performance were investigated and adjusted to improve performance. The derived model performance was shown, and its possibility was considered.

This paper is a study on the application position of skew in order to reduce the cogging torque of a magnetic geared synchronous motor (MGM). The cogging torque affects the noise and vibration of the motor, so it should be reduced as much as possible. To solve this problem, a conventional permanent magnet (PM) synchronous motor is skewed to a PM. However, unlike other synchronous motors, the MGM has pole pieces (PPs), and a larger cogging torque is generated due to a larger reluctance difference. There have been few studies on the reduction of cogging torque of MGM, so it is essential to study the skew structure of MGM. Therefore, this paper has derived the optimum skew method by comparing and analyzing three models of MGM skewed to PM, PP, and PM and PP simultaneously.

This paper reports the design of a magnetic-geared permanent magnet synchronous motor (MG-PMSM) for a 45 kW tram traction system based on high torque density. In the case of the existing tram driving system, due to mechanical reduction gear and induction motor, it causes power transmission loss, low efficiency, and difficulty in lightweight. To solve this problem, research on the MG-PMSM, which combines a contactless magnetic gear with a high-power-density PMSM, is being actively conducted. This motor has a double rotor structure, and the inner rotor, including permanent magnet, and the outer rotor composed of pole-pieces rotate at different mechanical speeds. However, it is hard to design a tram driving system with a high torque density within limited conditions, because only one rotor in MG-PMSM is used as an output. In addition, there is no study conducted from basic design to final design, including gear ratio and topology selection in MG-PMSM for tram. Therefore, this paper presents the design process of MG-PMSM with high torque density to be applied to the 45 kW–class tram driving system. After designing the magnetic gear part that increases torque and efficiency by selecting an appropriate topologies-and-gear ratio that meets the constraints, the final finite elements method (FEM) model and electromagnetic field analysis results were derived by considering the number of poles and the number of slots. Through this, we confirmed that it is superior in output characteristics compared to the existing induction motor + mechanical gear.

This paper presents optimal rotor permanent magnet (PM) and rotor pole-piece skew to improve the total harmonic distortion (THD) of the back electromotive force (Back-EMF) in magnetic geared permanent magnet synchronous motor (MG-PMSM) for traction. MG-PMSM is a system that integrates a magnetic gear and a PMSM which can minimize the size of the driving system and reduce power loss because there is no mechanical friction unlike the existing motor. For this reason, it is more advantageous in terms of output density and efficiency. However, MG-PMSM has a pole-piece rotor for magnetic flux modulation, which can produce additional spatial harmonics in back electromotive force (back-EMF). In addition, this motor has inevitable to have a salient permanent magnet structure for the stator due to magnet loss, and in the case of winding methods, fractional slot concentrated winding (FSCW) is mainly used, which also causes additional harmonics. THD in back-EMF adversely affects torque ripple and make accurate position control difficult. Therefore, in this paper, THD in back-EMF is reduced by focusing on the optimal rotors skew. Considering the characteristics of MG-PMSM, skew is applied to each rotor, and then compared and analyzed with the proposed model.