To improve gas hydrate storage and transportation technology, ferromagnetic intermetallic compound NiMnGa particles with martensitic transformation endothermics were used to form micro/nanofluids with sodium dodecyl sulfate (SDS) to further strengthen the gas hydration process. In this work, the kinetic process of gas hydration in NiMnGa fluids with different concentrations (0, 0.1, 1, 2, and 3 wt.%) was investigated using a rotating magnetic field gas hydration separation experimental setup. The results show that the induction time of the 3 wt.% NiMnGa system was shortened by 98.3%, the gas consumption was increased by 50.5%, and the gas consumption rate was increased by 351.9% compared with the SDS system. Therefore, it is inferred from the mass transfer that NiMnGa micro/nanofluids can accelerate the formation of hydrates.
31 March 2026 in Frontier materials & technologies
Problem. Currently used materials for ureteral stents are unable to eliminate inflammation, exhibit low strength, and require a second surgery for removal. Metallic bioresorbable stents can reduce the burden on the patient’s body and eliminate additional operations for product removal. Aim. To roduce a new biocompatible Zn-1 %Cu-1 %Mn alloy and, using equal-channel angular pressing at elevated temperature, to develop an improved set of mechanical properties for potential application as a material for ureteral stents. Methods. The Zn-1 %Cu1 %Mn alloy was subjected to equal-channel angular pressing at 200 °C (8 passes, route Bc). The microstructure and elemental composition were studied using transmission electron microscopy with energy-dispersive analysis. Mechanical properties were evaluated under uniaxial tension (strain rate of 10–3 с –1 , at least 3 samples per each condition), Vickers microindentation with construction of hardness distribution maps, and fractographic analysis of fracture surfaces using a scanning electron microscope. Results. By indexing diffraction patterns, it was established that the deformation processing promotes the precipitation of MnZn13 phase particles, which may have a strengthening effect. Fractographic analysis of fractured samples after tension showed a change in the fracture character from brittle to ductile with deep dimples. Carrying out equal-channel angular pressing (ECAP) for 8 passes at elevated temFrontier Materials & Technologies. 2026. № 1 17 Абдрахманова Э.Д., Хафизова Э.Д., Поленок М.В. и др. «Влияние высокотемпературного РКУП на структуру и механические…» peratures allowed increasing the ultimate tensile strength by 2.3 times, the offset yield strength by 3 times, and the percentage elongation by 8 times. The distribution of microhardness values becomes more uniform with a n increase in passes from 2 to 8, and the gap between the smallest and largest values decreases. Conclusions. It was established that the deformation method (ECAP, 8 passes) for the new biocompatible Zn-1 %Cu-1 %Mn alloy develops an improved set of mechanical properties, which opens up possibilities for its application in medical purposes.
1 January 2025 in Reviews on Advanced Materials and Technologies
Interest in biodegradable materials for temporary implants based on zinc alloys has been growing annually. The Zn-Fe-Mg alloys are of special interest, as each of its constituent elements is independently considered as biodegradable metallic material. This study presents a comprehensive investigation of the Zn-1%Fe-1%Mg and Zn-1%Fe-5%Mg alloys subjected to high-pressure torsion. A comparative analysis was conducted on the microstructure of the alloys in both as-cast and deformed states, highlighting differences in their phase composition, strength and cytotoxicity. When the magnesium content exceeds 3 wt.%, an additional phase (MgZn2) precipitates alongside the existing Mg2Zn11 phase. Deformation processing of the Zn-1%Fe-1%Mg alloy effectively reduces its brittleness and promotes a more homogeneous distribution of the Mg2Zn11 eutectic throughout the sample volume. In contrast, the Zn-1%Fe-5%Mg alloy retains excessive brittleness even after deformation. The addition of magnesium was found also to accelerate corrosion rates. Nevertheless, the strength, corrosion, and cytotoxicity properties of the Zn-1%Fe-1%Mg alloy meet the requirements for biodegradable materials.
30 July 2026 in Journal of Applied Polymer Science