Elvira Khafizova

Dr. Elvira Khafizova

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

27 June 2023 in Materials
Verified
Journal Article
Open access
PDF file
EKElvira Khafizova
Elvira Khafizova
EFElvira Fakhretdinova
Elvira Fakhretdinova
RIRinat Islamgaliev
Rinat Islamgaliev
MPMilena Polenok
Milena Polenok
VSVil Sitdikov
Vil Sitdikov
HYHakan Yilmazer
Hakan Yilmazer
It is known that zinc biodegradable alloys are a promising material for producing biomedical implants for orthopedics and vascular stents. Among them, the Zn-Ag-Cu zinc alloy is of special interest due to the antibacterial and antimicrobial properties of Ag and Cu. To improve the mechanical properties of the Zn-4Ag-1Cu zinc alloy, the effect of equal-channel angular pressing (ECAP) on the microstructure and strength has been investigated. The ECAP conditions for the Zn-4Ag-1Cu alloy were chosen by modeling in the Deform 3 D program (temperature and strain rate). The microstructure was analyzed using transmission electron microscopy, scanning electron microscopy and X-ray diffraction analysis. The study of strength was carried out by measuring the microhardness and tensile tests of small samples with a gauge dimension of 0.8 × 1 × 4 mm3. The microstructure after ECAP was characterized by equiaxed grains ranging in a size from 1.5 µm to 4 µm with particles in a size from 200 nm to 1 µm uniformly distributed along the boundaries. The ECAP samples showed a high strength of 348 MPa and good ductility of up to 30%, demonstrating their great potential as promising materials for producing medical stents.

1 January 2023 in Frontier materials & technologies
Verified
Journal Article
Open access
PDF file
OROOO RN-BashNIPIneft
OOO RN-BashNIPIneft
VSVil Sitdikov
Vil Sitdikov
IRInstitute of Physics of Molecules and Crystals of Ufa Research Center of the RAS
Institute of Physics of Molecules and Crystals of Ufa Research Center of the RAS
EKElvira Khafizova
Elvira Khafizova
UTUfa University of Science and Technologies
Ufa University of Science and Technologies
ЭХЭльвира Динифовна Хафизова
Эльвира Динифовна Хафизова
In this paper, the authors consider the mechanisms of formation of high-strength states in the Zn–1%Li–2%Mg alloy as a result of its processing by the high pressure torsion (HPT) method. For the first time, the study showed that using HPT treatment, as a result of varying the degree of deformation at room temperature, it is possible to increase the ultimate strength of a zinc alloy from 155 to 383 MPa (with an increase in the yield stress from 149 to 306 MPa) without losing its ductility. To explain the reasons for the increase in the zinc alloy mechanical properties, its microstructure was analyzed by scanning electron microscopy (SEM), X-ray phase analysis (XPA), X-ray diffraction analysis (XRD), and small-angle X-ray scattering (SAXS). Using XPA, the authors established for the first time that Zn(eutectic)+β-LiZn4(eutectic)→~LiZn3+Zn(phase)+Zn(precipitation) and MgZn2→Mg2Zn11 phase transformations occur in the zinc alloy during HPT treatment. SEM analysis showed that at the initial stages of HPT treatment, cylindrical Zn particles with a diameter of 330 nm and a length of up to 950 nm precipitate in β-LiZn3 phase. At the same time, the SAXS method showed that needle-like LiZn4 particles with a diameter of 9 nm and a length of 28 nm precipitate in the Zn phase. The study established that, only spherical Zn and LiZn4 particles precipitate at high degrees of HPT treatment. Precision analysis of the zinc alloy microstructure showed that HPT treatment leads to grain refinement, an increase in the magnitude of crystal lattice microdistortion, a growth of the density of dislocations, which are predominantly of the edge type. As a result of the analysis of hardening mechanisms, the authors concluded that the increase in the zinc alloy strength characteristics mainly occurs due to grain-boundary, dislocation, and dispersion hardening.

1 January 2022 in Frontier materials & technologies
Verified
Journal Article
Open access
PDF file
МПМилена Владиславовна Поленок
Милена Владиславовна Поленок
UUUfa State Aviation Technical University
Ufa State Aviation Technical University
EKElvira Khafizova
Elvira Khafizova
РИРинат Кадыханович Исламгалиев
Ринат Кадыханович Исламгалиев
Biodegradable materials, which have the ability to resorb in the body, are new and promising materials for medical implants. Currently, scientists carry out the investigations according to three directions: Mg, Fe, and Zn alloys. Zinc-based alloys and zinc have good solubility in the body, which meets the clinical requirements of implants. However, pure zinc has low mechanical properties, including hardness and tensile strength. Therefore, at present, the world scientific community is seeking ways to improve the properties of pure zinc by alloying. Another known approach is the ultrafine-grained (UFG) structure formation by the severe plastic deformation (SPD) methods, which are based on the large plastic deformations under high pressure and relatively low homologous temperatures. In this work, the authors studied the influence of high pressure torsion of pure zinc with various numbers of revolutions. The paper presents calculations of shear deformation after SPD. The authors investigated the dependence of mechanical properties and microstructure on the deformation degree. Tension tests at room temperature were carried out, and microhardness was measured. The authors studied the structure using scanning electron microscopy and optics. The study identified that the use of high pressure torsion leads to an increase in the tensile strength of pure zinc up to 140 MPa and ductility up to 40 % resulting from dynamic recrystallization.

1 January 2022 in Materials. Technologies. Design
Verified
Journal Article
Open access
PDF file
EKElvira Khafizova
Elvira Khafizova
MPMilena Vladislavovna Polenok
Milena Vladislavovna Polenok
ASArtur Ildarovich Salikhov
Artur Ildarovich Salikhov
RIRinat Kadykhanovich Islamgaliev
Rinat Kadykhanovich Islamgaliev
Development of new high strength biodegradable materials is one of the hot topics of world science. Recently, interest in zinc alloys for medicine has increased due to compliance with the clinical requirements for the degradation of the material in the body and the participation of zinc in a large number of processes in the body. The microstructure and mechanical properties of the Zn-4Ag-1Cu zinc alloy (wt.%) after high pressure torsion at temperatures 20 °C and 200 °C have been investigated in this paper. An ultrafine-grained structure with a size from 250 nm to 1.5 μm was produced as a result of dynamic recrystallization at HPT processing at 200 ℃, in addition dispersed particleswere observed throughout the HPT sample. The HPT samples processed at temperature of 200 °C demonstrated the ultimate tensile strength of 293 MPa with enhanced ductility of 30%. Создание новых биодегралируемых материалов с высокими механическими свойствами – одна из актуальных тем мировой науки. В последнее время значительно вырос интерес к цинковым сплавам для медицины за счет соответствия клиническим требованиям по деградации материала и участия цинка в большом количестве процессов в организме. В настоящей работе представлены результаты исследований микроструктуры и механических свойств цинкового сплава Zn-4Ag-1Cu (вес.%) после интенсивной пластической деформации кручением(ИПДК) при температурах 20 и 200 °С. Анализ микроструктуры показал, что в результате деформации произошла динамическая рекристализация с образованием ультрамелкозернистой структуры с размером зерен от 250 нм до 1,5 мкм. После ИПДК при 200 °С по всему объему образца дополнительно выделились дисперсные частицы. Образцы, подвергнутые ИПДК при температуре 200 °С, продемонстрировали повышенный предел прочности на растяжение 293 МПа с одновременным повышением пластичности до 30%.

30 September 2024 in Frontier materials & technologies
Verified
Journal Article
Open access
PDF file
VSVil Sitdikov
Vil Sitdikov
EKElvira Khafizova
Elvira Khafizova
MPMilena V. Polenok
Milena V. Polenok
The paper covers the production, analysis of the microstructure, crystallographic texture and deformation mechanisms of the ultrafine-grained (UFG) Zn–1%Mg–1%Fe zinc alloy demonstrating unique physical and mechanical properties compared to its coarse-crystalline analogs. The zinc alloy with improved mechanical properties was developed in two stages. At the first stage, based on the analysis of literature data, an alloy with the following chemical composition was cast: Zn–1%Mg–1%Fe. Then, the alloy was subjected to high-pressure torsion (HPT) to improve mechanical properties due to grain structure refinement and implementation of dynamic strain aging. The conducted mechanical tensile tests of the samples and assessment of the alloy hardness showed that HPT treatment leads to an increase in its tensile strength to 415MPa, an increase in hardness to 144HV, and an increase in ductility to 82%. The obtained mechanical characteristics demonstrate the suitability of using the developed alloy in medicine as some implants (stents) requiring high applied loads. To explain the reasons for the improvement of the mechanical properties of this alloy, the authors carried out comprehensive tests using microscopy and X-ray diffraction analysis. The microstructure analysis showed that during the formation of the ultrafine-grained structure, a phase transition is implemented according to the following scheme: Zneutectic + Mg2Zn11eutectic + FeZn13 → Znphase + Mg2Zn11phase + MgZn2particles + Znparticles. It was found that as a result of high pressure torsion in the main phases (Zn, Mg2Zn11), the grain structure is refined, the density of introduced defects increases, and a developed crystallographic texture consisting of basic, pyramidal, prismatic, and twin texture components is formed. The study showed that the resistance of pyramidal, prismatic and twin texture components at the initial stages of high-pressure torsion determines the level and anisotropy of the strength properties of this alloy. The relationship between the discovered structural features of the produced alloy and its unique mechanical properties is discussed.