A nanofluid is composed of a base fluid with a suspension of nanoparticles that improve the base fluid’s thermophysical properties. In this work, the authors have conducted experimental tests on an alumina-based nanofluid (Al2O3/H2O) moving inside a 3D-printed lattice channel. The unit cell’s lattice shape can be considered a double X or a double pyramidal truss with a common vertex. The test channel is 80 mm long and has a cross-sectional area, without an internal lattice with that has the dimensions H × W, with H = 5 mm and W = 15 mm. A nanofluid and a lattice duct can represent a good compound technique for enhancing heat transfer. The channel is heated by an electrical resistance wound onto its outer surface. The heat transfer rate absorbed by the nanofluid, the convective heat transfer coefficients, and the pressure drops are evaluated. The experimental tests are carried out at various volumetric contents of nanoparticles (φ = 1.00%, φ = 1.50% and φ = 2.05%) and at various volumetric flow rates (from 0.2 L/min to 2 L/min). The preliminary results show that in the range between 0.5 L/min ÷ 2.0 L/min, the values of convective heat transfer coefficients are greater than those of pure water (φ = 0) for all concentrations of Al2O3; thus, the nanofluid absorbed a higher thermal power than the water, with an average increase of 6%, 9%, and 14% for 1.00%, 1.50% and 2.05% volume concentrations, respectively. The pressure drops are not very different from those of water; therefore, the use of nanofluids also increased the cooling efficiency of the system.
21 March 2026 in International Journal of Thermophysics
The present paper presents experimental measurements of heat transfer on a cylinder, cooled by two rectangular jets of the same width but different height, H, in order to investigate the influence of the jet height on the local and the average cooling rates, because one of the problems in the heat transfer with jet flow is the convenience to choose the height of the jet in comparison to the height of the impinged object. The cylinder, heated by electric current, is set at several distances from the jet exit, x, on the symmetrical plane of symmetry, i.e. in a two-dimensional geometry, in order to find the optimal position which realizes the maximum heat transfer. The experimental heat transfer on the impingement shows that the local Nusselt number, defined with the cylinder diameter, D, is greater for the smaller slot because velocity is slightly higher but the average Nusselt numbers, defined with the cylinder diameter, D, are quite similar because the higher slot has a greater surface of impingement. Local and average Nusselt numbers are in qualitative agreement only if are compared with the same dimensionless distance, x/H, which can be interpreted as the ratio Rex/ReH, which is per unit of mass flow rate or is independent of the mass flow rate. Numerical simulations are carried out with a two-equations turbulent model using the RNG k-ε approach, on a cylinder with the same thickness of the experiments or without thickness. The numerical simulations of the cylinder without thickness are in acceptable agreement for what concern the average Nusselt numbers. The local Nusselt numbers are in fair agreement only if the cylinder has the thickness of the experiments, independently of the heat flow conditions, i.e. uniformly throughout the thickness or from the inner surface.
6 January 2025 in International Journal of Heat and Mass Transfer
Buoyancy-induced convection from a pair of staggered heated vertical plates suspended in free air is studied numerically with the main scope to investigate the basic heat and momentum transfer features and to determine in what measure any independent variable affects the thermal performance of each plate and both plates. A computational code based on the SIMPLE-C algorithm for pressure-velocity coupling is used to solve the system of the governing conservation equations of mass, momentum and energy. Numerical simulations are carried out for different values of the Rayleigh number based on the plate length, as well as of the horizontal separation distance between the plates and their vertical alignment, which are both normalized by the plate length. It is observed that an optimal separation distance between the plates for the maximum heat transfer rate related to the Rayleigh number and the vertical alignment of the plates does exist. Based on the results obtained, suitable dimensionless heat transfer correlations are developed for each plate and for the entire system.